CONTENTS 3. POWER-SHUTTLE DIAGNOSISPROGRAMM DEST 45 .185 3.1 PREPARATIONS FOR TRANSMISSION DIAGNOSIS WITH DEST 45 185 3.2 DEST 45 PROGRAM DESCRIPTION .................... 186 3.3 ERROR CODES POWER-SHUTTLE /DEST 45...... 201 3.4 DISPLAY POWERSHUTTLE................................... 202 3.5 ERROR CODE LIST WITH DESCRIPTION............. 203 3.6 OTHER INFORMATIONS ....................................... 214 3.7 SENSORS AND SOLENOID VALVES AT THE TRANSMISSION T-7100 215 3.8 ELECTRO-HYDRAULIC GEAR SHIFT T-7100 .......
216 3.9 SENSORS AND SOLENOID VALVES AT THE TRANSMISSION T-7200 217 3.10 ELECTRO-HYDRAULIC GEAR SHIFT T-7200 / T-7300 218 3.11 ERROR ANALYSIS................................................. 219 9. SERDIA (LEVEL III) ...................................................... 257 1. SETUP AND COMMUNICATIONS ..................................257 1.1 MINIMUM EQUIPMENT REQUIRED...................... 257 1.2 ORDERING............................................................. 258 1.3 SWITCHING ON AND INSTALLING THE SOFTWARE 259 1.4 USING THE PROGRAM......................................... 263 1.5 CLOSING THE PROGRAM .................................... 266 2.
ECU SELECTION ............................................................267 2.1 SELECTING TWO CONTROL UNITS..................... 267 2.2 PRINTING............................................................... 268 2.3 PROTOCOL............................................................ 269 2.4 IDENTIFICATION AND MEASUREMENT DATA..... 269 3. MEASURED VALUES ......................................................271 3.1 ACTUAL MEASURED VALUES (GENERAL) .......... 271 3.2 RAM-VALUES ........................................................ 276 3.3 DATA LOGGER (ONLY EMS2)............................... 280 3.4 INPUT/OUTPUT ASSIGNMENT.............................
280 3.5 CAN STATUS......................................................... 280 4. PREPARATIONS FOR DIAGNOSIS OF THE INFOCENTER ..........................................................221 4.1 PROGRAM DESCRIPTION .................................... 222 4.2 CONSTANT VALUES FOR INFOCENTER.............. 232 4. PARAMETERS ................................................................283 4.1 CONFIGURATION (GENERAL) .............................. 283 4.2 OVERALL PROGRAMMING................................... 284 4.2 CALIBRATION........................................................ 285 7.
ALL ROUND TESTER FOR LIFT AND ASM CONTROL UNIT ............................................................ 237 PRESENTATION SCREEN ....................................................237 MAIN MENU ..........................................................................237 1. MONITOR ........................................................................238 1.1 LIFT ........................................................................ 238 1.2 CONSOLE .............................................................. 240 1.3 ASM........................................................................ 240 1.4 POWER ..................................................................
241 1.5 SENSORS .............................................................. 242 5. ERROR MEMORY ...........................................................286 5.1 GENERAL............................................................... 286 5.2 ERROR TABLE....................................................... 287 6. EXTRAS ..........................................................................297 6.1 MAXIMUM SPEED ................................................. 297 6.2 LOGISTIC DATA..................................................... 297 6.3 LOAD SPECTRUM................................................. 298 6.4 MAINTENANCE INTERVAL EXCEEDED ................
298 6.5 OVERRIDE MEMORY ............................................ 298 6.6 MAINTENANCE DATA ........................................... 298 2. CONFIGURATION ...........................................................242 2.1 SPEED CONSTANTS ............................................. 243 2.2 OPTIONS................................................................ 243 3. CALIBRATIONS ..............................................................244 3.1 MINIMUM HEIGHT................................................. 245 3.2 MAXIMUM HEIGHT................................................ 245 3.3 LOCK SPEED.........................................................
246 3.5 TRANSPORT.......................................................... 247 3.6 STOP...................................................................... 247 3.7 CONTROL .............................................................. 248 3.8 FLOAT .................................................................... 248 7. TASKS .............................................................................299 7.1 EMR1 ..................................................................... 299 8. WHAT TO DO IF...? .........................................................303 8.1 SERDIA GENERAL.................................................
303 8.2 EMR1 ..................................................................... 305 4. ALARMS LIST .................................................................249 8. ALL ROUND TESTER FOR AXLE SUSPENSION CONTROL UNIT ............................................................ 251 PRESENTATION SCREEN ....................................................251 MAIN MENU ..........................................................................251 1. MONITOR ........................................................................252 1.1 SUSPENSION ........................................................ 252 2. PARAMETERS ................................................................253 3.
ALARMS LIST .................................................................255 4. CONFIGURATIONS .........................................................255 20-ii