3-' FRONT STEERING • 26 spline Spindle Flange 1~ [Ends with SIN 681500) ~43_~ -----~ Ref. Part No. Number DIy. Description IIDllEl 3Front Differential and Steering Parts Assembly Ref. Part (Incl. ref. no.'s 2, 4, 7, 9, 10, II, 12, 14, No. Number Qty. Description 15, 17 thru 22, 25, 26, 27, 29 thru 37, 40, 31. 160-160 2 Spindle Flange (26 spline)- 41, 42, 44thru 47, 50 and 51) Incl. ref. no. 14 1. 105-021 2 Nut (ll2-NC) 32. 160-187 2 Front Axle 2. 105-032 4 Bolt (3/B-NC x 3/4'1 33. 160-306 2 Tie Rod End (Incl. ref. no.'s 11 and 17) 3. 105·066 2 Bolt (1I2·NC x 1·3/4'1 34. 160-318 1 Spindle Housing (lefton front diff.) 4. 105-072 4 lock Washer (3/8'1 35.
160-319 1 Spindle Housing (right on front diff.) 5. 105-118 2 Washer (3/B'1 36. 160-321 1 Tie Rod 6. 105-340 4 Flange locknut(3/4-NC) 37. 160-336 2 2Spindle Shaft and Yoke (l-NS, 26spline) 7. 105-353 4 Bolt (3/4-NF x 2-5/8", GO 8, Nylok) 38. 160-686 4 Inverted Flare Elbow (3/16"T x 8. 105-371 4 Bolt (3/4-NC x 6-1/2'1 I/B-NPT x 9(0) 9. 105-403 1 Jam Nut (5/B-NC) 39. 160-653 2 Brake line (10" lG) 10. 105-404 2 Jam Nut (3/4-NF) 40. 161-007 1 3Front Differential 11. 105-405 2 CasUe Nut (9/16-NF) 41. 180-061 4 Spindle Washer 12. 105-410 2 lCasUe Nut (3/4-NF) 42. 180-279 2 lSpindle Washer (.765" 101 105-349 2 2SIotted Nut (1-NF) 181-381 2 2Spindle Washer (1.06" 10) 13.
105·424 10 lug Nut (3/4-NF) 43. 180-320 2 Front Axle Pivot Shaft 14. 105·426 10 lug Bolt (3/4-NF x 1·13/16") 44. 180-724 2 Cross and Bearing (Incl. ref. no. 20) 15. 105·451 12 Wave Spring Washer 45. IIiPIiI!II 2 Axle Yoke 16. 105·462 1 Bolt (5/8·NC x 2·1/4'1 182-103 2 Axle Yoke (replacement) 17. 105-509 2 Cotter Pin (1/8" x 1'1 46. 205-671 2 Hub Cap 18. 105-518 2 lCotter Pin (118" x 1-1/2'1 47. 301-151 4 Spindle Bolt lock 105-516 2 2Roll Pin (3/16" x 1-1/2'1 190-273 5Spindle Bolt Conversion Kit (Incl. ref. 19. 105-716 4 Setscrew (3/8-NC x 1/2'1 ne.'s 2,4, 7, 15,27,29,41 and 47) 20. 115-010 2 Zerk (1/8-NPT x 22-112°) 48. 301-822 2 Saddle Clamp 21. 115-004 4 Zerk (1/8-NPT x 450) 49.
312-090 1 Differential Mount 22. 115-006 2 Zerk (1/4-NF x 45°) 50. 110-095 2 lMachinery Bushing 23. 115-172 2 Pipe Collar (I/B'1 51. 182-020 1 Differential Yoke 24. 115-483 1 External Clip Ring IUsed with spindle shafts which have 3/4-NF threads. Wh~n replacing a 25. 125-260 4 Bearing 3/4-NF with l-NS spindle shaft you must order shaft, roll pm, washer and 26. 125-261 4 Race nut. See footnote 2. 27. 125-301 4 Bushing 2Used with spindle shafts which have l-NS threads. ., 28. 125-403 1 Bronze Bushing 3Refer toinstallation diagram 052-185. See footnote 4. 'For replacement assembly refer to FRONT STEERING - 43 spline Spmdle 29. 125-716 8 Urethane Flange Bushing Flange -(Beginswith SIN 6BI501)..
. . 30. 155·808 4 Internal Seal 5Refer toinstallation diagram 050-946 tomstall spmdle bolt kit. 3501!)-35019 31