John Deere 450DLC — Monitor Circuit Theory of Operation

TM2361 (24JUN08) 9015-15-12 450DLC Excavator Operation and Tests 062608 PN=456 Sub-System Diagnostics Work Mode Alarm Indicator—If the MCF detects a connects terminal B18 on the monitor controller and malfunction in the work mode circuit, the MCF sends a terminal B6 on the MCF to ground. This causes signal through the CAN to the monitor controller. When auto-idle mode to be selected, and the auto-idle the monitor controller receives this signal, the work indicator to appear on the monitor display. For mode alarm indicator appears on the monitor display.

additional information on auto-idle, see Main Controller For information on diagnosing MCF circuit (MCF) Circuit Theory of Operation (Group 9015-15.) malfunctions, see Main Controller (MCF) Diagnostic and see Engine Speed Control System Operation. Trouble Codes. (Group 9001-20.) (Group 9010-05.) Pilot Shutoff Lever Indicator—When pilot shutoff Windshield Wiper and Washer Switch (S9)— switches 1 and 2 (S3 and S4) are in the same Windshield wiper and washer switch (S9) is used to position, terminal B19 on the monitor controller is select intermittent or continuous windshield wiper connected to ground. If terminal B19 is not connected operation and to activate the windshield washer motor.

to ground, the pilot shutoff lever indicator appears on The monitor controller supplies a 5-volt reference the monitor display. For additional information on the voltage (terminal C6) and a ground (terminal C9) to the pilot shutoff circuit, see Pilot Shutoff Circuit Theory of windshield wiper and washer switch. The monitor Operation. (Group 9015-15.) controller determines the position of the windshield wiper and washer switch from signals received at Engine Coolant Temperature Sensor Error terminal C3.

When the windshield wiper and washer Indicator—If the ECM detects a malfunction with switch is turned to the ON or one of the INT positions, engine coolant temperature sensor (B4) or if the the monitor controller momentarily connects terminals 9015 15 12 connection between the sensor and the ECM is open A2 and A11 to ground, energizing windshield wiper or shorted, the ECM sends a signal through the CAN relay (K6). to the monitor controller. When the monitor controller receives this signal, the engine coolant temperature When the windshield wiper and washer switch is sensor error indicator comes on. pressed, terminal B3 on the monitor controller is connected to ground.

This causes the monitor Fuel Sensor Error Indicator—If the ECM detects a controller to connect terminal A10 to ground, malfunction with fuel temperature sensor (B5) or if the energizing windshield washer relay (K9). connection between the sensor and the ECM is open or shorted, the ECM sends a signal through the CAN For additional information on the windshield wiper and to the monitor controller. When the monitor controller washer circuit, see Windshield Wiper and Washer receives this signal, the fuel sensor error indicator Circuit Theory of Operation. (Group 9015-15.) comes on.

Work Light Switch (S10)—When work light switch Monitor Display Alarm—Monitor warning alarm (H3) (S10) is in position 1, terminal B20 on the monitor notifies the operator when certain diagnostic trouble controller is connected to ground. This causes the codes or machine conditions exist which could damage monitor controller to connect terminal A1 to ground, the machine. Power is available from fuse (F19) at energizing drive light relay (K7). When the work light terminal 1 on the monitor warning alarm. When the switch is turned to position 2, terminal A6 is connected monitor controller connects terminal A3 to ground, the to ground. This causes the monitor controller to alarm activates.

connect terminals A1 and A5 to ground, energizing drive light relay (K7) and boom work light relay (K8). Auto-Idle Switch (S8)—When auto-idle switch (S8) is turned to the ON position, the auto-idle switch Continued on next page CS33148,00008E9 –19–21APR06–5/6