111 BACKFILL BLADE ASSEMBLY RT90, RT95, & RT115 REF NO. PART NUMBER QTY DESCRIPTION REMARKS 1. 105-416 2 WASHER (5/8") 2. 178-572 1 PIN (1.75" X 12.75") 4. 125-771 5 COMPOSITION BUSHING (1.25") 5. 300-7763 1 PIN 6. 181-982 1 TAPERED INSERT (1.25") 7. 107-434 1 ROLL PIN 3/8 X 1-5/8 8. 106-164 1 FLG LK SCREW (M10-1.50 X 30mm) 9. 181-981 1 TAPERED INSERT (1") 10. 183-767 1 TAPERED PIN (25.4mm X 60mm) 11. 125-770 1 COMPOSITION BUSHING (1") 12. 125-822 2 COMPOSITION BUSHING (1.750") 3. 151-057 - CYL (2.0" X 1.25" X 8.0") SEE FOOTNOTE 2 13. 331-475 1 PIVOT 14. 125-773 4 COMPOSITION BUSHING (1.750") 15. 106-470 4 FLG SCREW (M16-2.00 X 40mm) 16. 181-975 2 TAPERED INSERT (1.75") 17.
178-584 1 TAPERED PIN (1.750" X 13.90") 18. 183-768 1 TAPERED PIN (44.4mm X 205mm) 19. 308-921 1 LIFT ARM 20. 151-070 - CYL (3" X 1.75" X 8") 21. 300-8635 1 LOW ANGLE BACKFILL BLADE, 80" SEE FOOTNOTE 1 22. 151-202 - CYL (2" X 1" X 3.38") 23. 178-532 1 PIN (1.750" X 7.000") 24. 314-104 2 TILT BLADE RETAINER 26. 105-475 2 WASHER (1/2") 25. 178-394 2 TAPERED PIN (1.250" X 4.250") 28. 106-012 6 FLANGE BOLT (5/8-NC X 3") 27. 105-830 4 FLG LK BOLT (1/2-NC X 1-1/4") 29. 309-138 2 RETAINER 30. 106-383 2 FLG LK SCREW (M10-1.50 X 30mm) 31. 331-751 1 80" CUTTING EDGE 32. 322-360 2 FITTING GUARD (3.0" CYL) 33. 106-330 4 SCREW (M8-1.25 X 70mm) 34.
106-386 4 FLG LOCKNUT (M8-1.25) OPTION OPTION OPTION OPTION USE LOCTITE 242 35. 105-1187 2 SCREW (M10-1.5 X 35mm) 36. 105-1188 2 TAPERED PIN (1.250" X 2.560") 37. 107-537 2 SCREW (M10-1.5 X 20mm) 38. 300-8460 2 TAB PIN (1.250" X 2.57") USE LOCTITE 242 NOT SHOWN: FOOTNOTES: 1. BACKFILL BLADE 300-4321 IS SUPERSEDED BY 300-8635 ON RT90, RT95, AND RT115. RT95M BEGINS WITH S/N CMWRT95MJ90000296 RT95H BEGINS WITH S/N CMWRT95HK90000364 RT115 BEGINS WITH S/N CMWR15T3K90000130 2. EARLIER MODELS USE P/N 183-766 TAPERED PIN (31.7mm X 90MM) WITH 106-469 FLG SCREW (M12-1.75 X 30mm) NOTE: 15 ID0115816