165 BACKFILL BLADE HYDRAULICS 1. 153-074 2 HOSE (06OFX90-88"-3000) REF NO. PART NUMBER QTY DESCRIPTION REMARKS LIFT 2. 153-968 1 HOSE (04OFX90S-82"-5000) SWING SWING TILT 3. 515-310 2 HOSE (04OFX45-22"-5000) 4. 515-137 2 HOSE (04OFX90-90"-3000) 6. 154-261 2 CONNECTOR (04O-08S) 5. 106-327 2 SCREW (M8-1.25 X 30mm) 7. 154-374 2 CONNECTOR (04O-08S, ORF) 8. 151-057 2 CYL (2.0" X 1.25" X 8.0") SEE FOOTNOTE 1 9. 154-293 1 BRANCH TEE (04S-04O-04O) 10. 154-278 1 CONNECTOR (04S-04O) 11. 151-070 1 CYL (3" X 1.75" X 8") 12. 151-202 1 CYL (2" X 1" X 3.38") 13. 154-342 2 CONNECTOR (06S-06O90) 14. 154-252 3 CONNECTOR (04S-04O90) SEE FOOTNOTE 1 SEE FOOTNOTE 1 15. 307-416 1 BK BRACKET 16.
154-229 2 BK CONNECTOR (06O-06O90BK) 17. 154-355 2 BK CONNECTOR (04O-04O90BK) 18. 154-921 1 HOSE (04OFX-54"-3000-AR) TILT 19. 154-929 1 HOSE (06OFX90-19"-3000) 20. 515-221 1 HOSE (06OFX90S-28"-3000) LIFT LIFT 21. 106-386 2 FLG LOCKNUT (M8-1.25) 22. 154-316 1 RUN TEE (04S-04O-04O) 24. 158-033 - HYD. CONTROL VALVE (3-SPOOL) 23. 153-967 1 HOSE (04OFX90S-90"-5000) ENDS WITH S/N 5Y0446. OBSOLETE BEGINS WITH S/N 5Y0447, USE FLOAT KIT 500-2020 SWING 159-809 - HYD. CONTROL VALVE (3-SPOOL) 25. 117-691 1 ABRASION SLEEVE (1.25" X 68") 26. 115-920 1 ABRASION SLEEVE (2.38" X 70") 28. 154-222 1 CONNECTOR (06O-08S) 27. 514-294 1 CONNECTOR (08S-06O, ORF) 31. 105-818 4 BOLT (1/4-NC X 1-1/2") 30.
110-958 2 BACKUP PLATE 29. 110-866 2 CLAMP SET (1/2") SEE FOOTNOTE 2 32. 110-332 1 BOLT-ON CLAMP (1-5/8") 33. 105-003 2 FLG LOCKNUT (5/16-NC) 34. 110-333 1 BOLT-ON CLAMP (1") SEE FOOTNOTE 3 SEE FOOTNOTE 3 SEE FOOTNOTE 3 35. 117-328 1 ABRASION SLEEVE (1.00" X 18") 36. 117-672 2 ABRASION SLEEVE (1.00" X 20") 37. 117-409 1 ABRASION SLEEVE (1.00" X 28") 38. 153-973 1 HOSE (04OFX45-54"-3000-AR) 39. 154-344 2 UN RUN TEE (06OFX-06O-06O) 40. 154-326 2 CAP (06OF) TILT 41. 116-259 AR BULK EDGE (1/2", SOLD PER FT) USE 1 @ 20" & SEE FOOTNOTE 4 FOOTNOTES: 1. REFER TO PARTS PAGE "BACKFILL BLADE ASSEMBLY" FOR CYLINDER INSTALLATION HARDWARE. 3.
#110-333, 105-003 & 110-332 ATTACH TO STUD BOLTS ON FRAME PLATES. 2. CLAMP SET (110-866) BOLTS ONTO WELD PLATE ON BFB LIFT ARM. 4. USE EDGING ON FRAME WHERE HOSE'S PASS THRU. NOTE: REFER TO O-RING CHART (800-301) IN BACK OF THE BOOK FOR REPLACEMENT OF O-RINGS. 11 ID0115813