— AMCP 706-286 — Engineering Design Handbook (1963)

Downloaded from https://www.everyspec.com STRUCTURES j '' , of a high speed aircraft or the contro, vanes lyn. The model showr in I'igure 4-1 was of a rnissilp. The wave drag is proportioaial made of cast aluminum alloy and had a wall !o the square of the wing thickness, hence the thickness f 9.5 inch. After 50 seconds of acrodynarnicist would like to have as thin a ieating at a tunnel stagnetio: presst-re bf wing as possible. The ability of the struc- 16) psia an.. a stagnation tpnperature of ture withi the wing to carry certain loads, 1995 "R, a moderate amount of melting occur- however, increases approximately as the red at the stz.gnatior region.

Of interest is square of the wing thickness. In general, the symmetric manner in which the molten such cases of conflicting inteiE-Ls are settled rietal recrystallized after being carried . by a compromise; this is almost always true downstream to the relatively cooler surface in design problems. Should he aerodynamic of the model. The model shown in Figgre requirement be very severe ard have high 4-2 was tested for 62 seconds. The model and priority, decreasing the wing thickness may test conditions were identical to those dps- lead to a prohinitively high weight for the cribed above except that the stagnation tern- wing design. Jn this eve'., the structural perati:e was 203 0 °R.

The melted portion of designer-may have to" study lhe possibility of the nose cone was observed to have disinte- a more efficient structural configuration, grated into relatively,large -particles. stronger alloys of conventional materials, or Structural design for aerodynamic heating even the use of a neiv material, is undobutedly one of the major problem in The example ci ed has been over implified areas for the missile designer and analyst in order to illustrate the maner in which the Under the influence of high heating rates, interests of one group affect those of anc.her.

and the resulting high temperatures, mate- Onr could go fuether with Che above exa-s ile r'als which had performed satisfactorily in cnd show the effect that an extremely .'-in the paet may be wholly inadequate, In the wing may have on other aspects of the dcli:,,. most critical regions (nose cone, control sur- The thin wing may introduce problems in faces), several solutions may be considered connection with the housing of certain corn- by the designer to cope with the adverse ponents.

Generally speaking, changes in one effects of elevated temperatures on material design feature will affect many ocher aspects properties and structural behavior of missile of the design; the importance of making in- components. Even in regions subject tc mod- tePigent compromises cannot be overempha- erate conditions of thetmal environment, the sized in the success of an aircraft or mis.- structural design problems are iormidable. sile design. Structural design configurations for aerody. namic heating may be conveniently classified 4.3. AERODYNAMIC HEATING as (1) unprotected, (2) inbulated, (a) Probably the most serious problems aris- coolcd, or a gombination of these.

ing from the aerodynamics of flight that 4-3.1. Unprotected Structures, Unprotected affect the missile structural designer are structures may be defined as structvres that tho&e associated with aerodynamic heating. do not employ any fluid coolant or special Depending on the speed, character of the insulators to deal with the thermal input boundary layer, and other factors, the heat from the boundary layer air. They present input over crtical portions of the s~wface of unusually difficult design problems inasmuch a missile can attain values of the order of as the designer is concerned directly w'*th 10" Btu/ft"/hr.

The qualitative and quanti- material properties and structural behavior tative aspects of thi3 phenomenoai are coy- at eleva ed temperatures, aeroelastic, and ered in another volume of this series, propellant task problems. In addition, the The effects of aerodynamic heating on nose designer must seriously consider transfer of cone models are shown in Figores 4-1 and heat to the interior of the missile because 4-2. These tests were run in the hypersonic there may be temperature limitations on the tunnel at the Polytechnic Institute of Brook- proper functioning of electronic and other 58