DVP-ES2/EX2/SS2/SA2/SX2/SE&TP Operation Manual - Programming 2-16 OFF STOP RUN Special ES2 SA2 Latch Function SS2 SX2 Attrib.
Default M EX2 SE -ed ON RUN STOP M1156* Enabling the mask and alignment mark function on I400/I401(X4) corresponding to Y0 ○ ○ ○ ○ OFF OFF - R/W NO OFF M1157* Enabling the mask and alignment mark function on I500/I501(X5) corresponding to Y1 V3.41 ╳ ╳ ╳ OFF OFF - R/W NO OFF M1158* Enabling the mask and alignment mark function on I600/I601(X6) corresponding to Y2 ○ ○ ○ ○ OFF OFF - R/W NO OFF M1158* Enabling the mask and alignment mark function on I700/I701(X7) corresponding to Y3 V3.41 ╳ ╳ ╳ OFF OFF - R/W NO OFF M1161 8/16 bit mode (ON = 8 bit mode) ○ ○ ○ ○ OFF - - R/W NO OFF M1162 Switching between decimal integer and binary floating point for SCLP instruction. ON:
binary floating point; OFF: decimal integer ○ ○ ○ ○ OFF - - R/W NO OFF M1167 16-bit mode for HKY input ○ ○ ○ ○ OFF - - R/W NO OFF M1168 Designating work mode of SMOV ○ ○ ○ ○ OFF - - R/W NO OFF M1177 Enable the communication instruction for Delta VFD series inverter. ON: VFD-A (Default), OFF: other models of VFD ○ ○ ○ ○ OFF - - R/W NO OFF M1178 Enable knob VR0 ╳ ╳ ○ ○ OFF - - R/W NO OFF M1179 Enable knob VR1 ╳ ╳ ○ ○ OFF - - R/W NO OFF M1180 The EX2/SX2 model reads analog-to- digital values immediately. ○ ╳ ╳ ○ OFF - - R/W NO OFF M1181 The EX2/SX2 model outputs digital-to- analog values immediately.
○ ╳ ╳ ○ OFF - - R/W NO OFF M1182* M1182 = ON, disable auto-mapping function when connected with left-side modules. For SA2 /SX2/SE models, values of AIO modules will be auto-mapped to D9800 and above. If the left side is connected with a communication module, additional 10 words will be occupied. Ex: 04AD-SL + EN01-SL + SA2, average value of Ch1~Ch4 of 04AD-SL maps to D9810~D9813. ╳ ╳ ○ ○ ON - - R/W NO ON M1183* M1183 = ON, disable auto mapping function when connected with special modules #: ES2/EX2: OFF; SE/SA2/SX2:
ON (maps to D9900 and later) ○ ╳ ○ ○ # - - R/W NO # M1190 Set Y0 high speed output as 0.01 ~ 10Hz ○ ○ ○ ○ OFF OFF - R/W NO OFF M1191 Set Y1 high speed output as 0.01 ~ 10Hz ○ ○ ○ ○ OFF OFF - R/W NO OFF M1192 Set Y2 high speed output as 0.01 ~ 10Hz ○ ○ ○ ○ OFF OFF - R/W NO OFF M1193 Set Y3 high speed output as 0.01 ~ 10Hz ○ ○ ○ ○ OFF OFF - R/W NO OFF M1196 Keep connectivity flag for ETHRS instrucitons (available for SA2/SX2 V2.89, SE with firmware V1.83 and later ) ╳ ╳ ○ ○ OFF OFF - R/W NO OFF M1197 In execution flag for ETHRS instrucitons (available for SA2/SX2 V2.89, SE with firmware V1.83 and later ) ╳ ╳ ○ ○ OFF OFF - R/W NO OFF M1198 Error flag for ETHRS instrucitons (available for SA2/SX2 V2.89, SE with firmware V1.83 and later ) ╳ ╳ ○ ○ OFF OFF - R/W NO OFF M1200 C200 counting mode (ON:
count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1201 C201 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1202 C202 counting mode ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1203 C203 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1204 C204 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1205 C205 counting mode (ON :count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1206 C206 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF M1207 C207 counting mode (ON: count down) ○ ○ ○ ○ OFF - - R/W NO OFF