DVS instruction sheet-03262012

100M Orange OFF The port is connected at a speed of 10 Mbps or disconnected. ON The Network communication connection has been established. OFF The Network communication connection has not been established. ON The communication is interrupted, or there is a power failure. OFF The communication is not interrupted, or there is no power failure. 100M Orange OFF The port is connected at a speed of 10 Mbps or disconnected. ON The Network communication connection has been established. OFF The Network communication connection has not been established. ON The communication is interrupted, or there is a power failure. OFF The communication is not interrupted, or there is no power failure.

The DIP switch is not enabled. Orange OFF The port is connected at a speed of 10 Mbps or disconnected. ON The Network communication connection has been established. OFF The Network communication connection has not been established. The 10/100Base-T(X) ports of the DVS series switches are used to connect to Ethernet. They can support MDI (NIC – type) and MDI-X (HUB/Switch-type) modes, the pin definition of the Ethernet cable is as follows. ѓ DVS-005W01-MC01 / DVS-008W01-MC01 / DVS-016W01-MC01 ON The fiber port is connected at a speed of 100 Mbps.

DVS-005 DVS-008 DVS-016 Dimension(mm) 145.3 (H) x 45(W) x 108.7(D) 145.3(H) x 75(W) x 108.7(D) Weight (g) 300 430 490 ђ For more information about the product, please visit http://www.delta.com.tw. LED Color Status Description ON The port is connected at a speed of 100 Mbps. LED Color Status Description ON The port is connected at a speed of 100 Mbps. LED Color Status Description LED Color Status Description ON The port is connected at a speed of 100 Mbps. 100M (on the a Mechanical Characteristics ON The power is supplied normally. Blinking The data is being transmitted. LINK/ACT Green ѓ DVS-005W01 / DVS-008W01 / DVS-016W01 The DIP switch is not enabled. ON The power is supplied normally.

ON The power is supplied normally. Blinking The data is being transmitted. LINK/ACT Green ON The power is supplied normally. PWR2 Green ON The power is supplied normally. 100M Green OFF The fiber port is not connected. Blinking The data is being transmitted. LINK/ACT Green Case IP30 Aluminum metal case PWR Green OFF The power is not supplied. PWR1 Green OFF The power is not supplied. PWR2 Green OFF The power is not supplied. PWR1 Green OFF The power is not supplied. OFF The power is not supplied.

PIN MDI Mode Definition MDI-X Mode Definition ` Ethernet Interface ѓ 10/100Base-T(X) Connection 1 Tx+ Rx+ 2 Tx- Rx- 3 Rx+ Tx+ 6 Rx- Tx- ѓ 100Base-FX Connection ALARM Red ALARM Red RJ-45 port) Step 1: Insert the wall mounting bracket into the slot on the rear panel of the DVS series switch, and tighten the screw on it, as shown in the diagram below. Step 2: Place the wall mounting bracket in an appropriate position, and tighten the two screws on the bracket and the DIN clip. Both sets of DC input can be connected to a wide range of power sources (12~48VDC). If one power source Step 1 :

Insert the negative and positive DC wires into the terminal block, and make sure that the positive DC Step 2 : To prevent the loose DC wires , tighten the wire clamp screws on the terminal block connector with the Step 3 : Insert the plastic terminal block connector into the terminal block receptor on the DVS series switch. Except the DVS-005I00, the DVS series switches are equipped with two sets of DC input (PWR1 / PWR2). NOTE: Grounding the ground terminal on the DVS series switch can avoid the noise effect due to the Step 1: Insert the flat-blade screwdriver into the DIN clip and pull the DIN clip downward.

\ Wiring the Redundant Power Input fails, the other live source can work as a backup to ensure that the machine operates normally. wire is connected to V1+ or V2+, and that the negative DC wire is connected to 0V. circuit, and the alarm LED will be on. circuit, and the alarm LED will not be Step 2: Pull the DVS series switch, and you can remove it from the DIN-Rail. electromagnetic interference (EMI). ] Wiring the Alarm Contact flat-blade screwdriver.

ђ Wall Mounting ђ Removal ENGLISH 3 This instruction sheet only provides information on electrical specifications, general specifications, installation and 3 The components and the IC on the circuit board can be easily damaged by static electricity; therefore DO NOT touch them before precautions against static electricity are done. To prevent the danger and damage from occurring, people who are not maintenance staff should not operate or accidentally hit the body of the DVS series switch. Besides, DO 3 This product is equipped with Class 1 LASER/LED components.

DO NOT stare directly at the LASER/LED beam to 3 Please read this instruction sheet thoroughly, and follow the instructions to prevent the damage to the device or injury Thank you for purchasing the DVS Unmanaged Industrial Ethernet Switches. The DVS series switches including 5, 8, and 16-port smart switches. Except the DVS-005I00, The DVS series switches are equipped with the intelligent alarm function, and allow the wide range of operating temperature (-40 to 75 o C). The DVS series switches are designed to support the application in any rugged environment and comply with UL, CE NOT touch any terminal when the power is switched on. Z Warning avoid serious injury to your eyes.

X Introduction and FCC standards. Y 3. Wall Mounting Plate 4. Warranty Card [ ѓ to the staff. 4. Auto-MDI/MDI-X 2. Instruction Sheet ђ Mounting wiring. PWR 100M Green Orange ON OFF ON OFF The power is supplied normally. The power is not supplied. The port is connected at a speed of 100 Mbps. The port is connected at a speed of 10 Mbps or disconnected. ALARM Red ON The communication is interrupted, or there is a power failure. OFF The communication is not interrupted, or there is no power failure. The DIP switch is not enabled. PWR1 Green ON The power is supplied normally. OFF The power is not supplied. PWR2 Green ON The power is supplied normally. OFF ON The power is not supplied.

The port is connected at a speed of 100 Mbps. OFF ON Blinking The port is connected at a speed of 10 Mbps or disconnected. The Network communication connection has been established. The data is being transmitted. OFF The communication is not interrupted, or there is no power failure. The DIP switch is not enabled. PWR1 Green ON OFF The power is supplied normally. The power is not supplied. LED Color Status Description OFF The power is not supplied. 100M 100M (on the Green Orange ON The fiber port is connected at a speed of 100 Mbps. OFF ON The fiber port is not connected. The port is connected at a speed of 100 Mbps.

OFF ON Blinking The port is connected at a speed of 10 Mbps or disconnected. The Network communication connection has been established. The data is being transmitted.

Page 1