Command List of the Alphabetical Order 1 "Priority" indicates the function is executed with priority. ESC/Label Command List Rev. C SHEET25 CW-C4000 series Command Function identifier Command name Description Classification Command code Description of parameters Definition range for ESC/Label Definition range Factory-set initial value Corresponding ZPL II command Priority 1 ^S(C LR Set resolution Sets resolution (printing, rendering, or rendering of background image loaded with the overlay function). Printer setting ^S(CLR,b,c b=B: Background image rendering resolution [dpi] c = 200/300/600 c = 200/300/600 600 Low b=M: Print resolution magnification c = A/B A: Normal resolution B:
Low resolution c = A/B A: Normal resolution B: Low resolution A ^JM b=P: Print resolution [dpi] c = 200/300/600 c = 200/300/600 200 [dpi] is to be used only when 200 [dpi] was specified for ^S(CLR,Z: print resolution of replaced printer. 600 ^MU b=R: Format base in dots per inch [dpi] c = 150/ 200/300/600 c = 150/ 200/300/600 600 ^MU b=Z: Print resolution of replaced printer [dpi] c = 200/300/600 c = 200/300/600 600 ^S(C LS Set media Sends media layout (gap between labels, left gap, label length, or label width). Media configuration ^S(CLS,b,c b=C: Gap between labels [dot] 0 ≤ c ≤ 9999 0 ≤ c ≤ 142 71 Low b=G: Left gap [dot] 0 ≤ c ≤ 9999 0 ≤ c ≤ 48 48 b=L:
Label length [dot] 0 ≤ c ≤ 99999 188 ≤ c ≤ 9600 4129 b=P: Label width [dot] 0 ≤ c ≤ 9999 506 ≤ c ≤ 2551 2551 ^S(C LV Set media size error Enables/disables media size error detection. Media configuration ^S(CLV,b,c b=H: Media size error (width) detection c = E/D E: Enabled D: Disabled c = E/D E: Enabled D: Disabled D Low b= V: Media size error (length) detection c = E/D E: Enabled D: Disabled c = E/D E: Enabled D: Disabled D ^S(C MF Set feed operation Sets the media feed sequence when the power is turned on and the media is changed, or the media suction strength. Printer setting ^S(CMF,b,c b=H: Operation at change media c = C/F/G/L/N/S C: Calibration F: Feed G: Feed and cut L:
Measure media length N: No feed S: Short calibration c = C/F/G/L/N/S C: Calibration F: Feed G: Feed and cut L: Measure media length N: No feed S: Short calibration F ^MF Low b=M: Manual paper suction strength 1 ≤ c ≤ 10 1 ≤ c ≤ 10 10 b=P: Operation at power on c = C/F/G/L/N/S C: Calibration F: Feed G: Feed and cut L: Measure media length N: No feed S: Short calibration c = C/F/G/L/N/S C: Calibration F: Feed G: Feed and cut L: Measure media length N: No feed S: Short calibration N ^MF b=S: Paper suction strength c = E/D E: Enabled D: Disabled c = E/D E: Enabled D:
Disabled D ^S(C MN Enable/disable nozzle clogging recovery function Sets whether the automatic nozzle clogging recovery function is enabled/disabled. Printer setting ^S(CMN,b,c b=S: Enable/disable nozzle clogging recovery c = E/D E: Enabled D: Disabled c = E/D E: Enabled D: Disabled E Low