Parts for BMW R 26 to R 27 34 11 2 060 121 Adjusting screw for brake Bowden cable 34 11 2 060 132 “BERAL” brake linings, set with rivets 34 11 2 072 235 Brake cable 34 21 4 044 115 Wing nut for brake actuating rod “polished brass” 71 60 0 009 794 Tank rucksack with base-plate, incl. rainproof cover 07 11 0 000 694 Lens head countersunk screw M6 x 18 for manual 33 12 0 018 044 Crown ring set, transmission ratio 35:
9 07 11 0 035 319 Lens head countersunk screw M6 x 22 for manual gearshift lever knob 33 12 0 026 232 Driver for crown ring set in rear axle drive 33 12 3 038 105 Snap ring for Hardy washer Model-specific parts R 26 07 11 9 913 661 Hexagon bolt M8 x 30 V2A polished for headlamp bracket gearshift lever knob 33 21 3 038 183 Protecting ring for Hardy disc 33 52 0 007 844 Cover black painted sheet steel f.
rear shock absorber 35 21 0 027 287 Return spring for footbrake lever, V2A 35 21 4 044 159 Brake actuating rod, V2A “polished” 11 25 0 000 626 Piston with rings and piston bolts 1st oversize 11 25 0 000 627 Piston with rings and piston bolts 2nd oversize 11 25 0 000 628 Piston with rings and piston bolts 3rd oversize 11 25 0 000 629 Piston with rings and piston bolts 4th oversize 11 81 1 034 123 Spacer tube for engine bracket, bottom 11 81 4 034 162 Spacer tube for engine bracket, front, top 07 11 9 914 089 Hexagon bolt M8 x 1 x 68 for saddle 07 11 9 914 364 Hexagon bolt M10 x 1 x 68 for saddle 33 53 3 054 312 Sliding bush for rear wheel suspension 33 53 3 054 320 End cap for fork slider 36 31 4 038 127 Spacer tube for wheel bearing, inner 36 31 4 038 131 Spacer sleeve for wheel bearing, outer 36 31 4 038 142 Thrust sleeve for wheel bearing, left/right 36 31 4 038 143 Thrust sleeve for wheel bearing left, large shoulder 36 31 4 038 155 Felt washer for wheel bearings 36 31 4 038 157 Felt washer capsule for wheel bearings 36 31 4 038 162 Sealing cap on wheel hub 36 31 4 038 173 Spoke retainer 36 31 5 590 020 Spoke 140 x M 3.5 07 11 9 930 065 Spoke nipple M 3.5 07 11 9 940 445 Bolt for clutch lever on gearbox 07 11 9 963 107 Sealing washer for locking screw 34 11 0 007 840 “Simplex” brake cable R 51/2 to R 67/3 34 11 0 007 842 “Sidecar” brake cable R 51/2 to R 67/3 07 11 9 963 108 Rubber ring for tool compartment locking screw 34 11 0 009 856 “BERAL” split-hub brake linings, set with rivets 34 11 2 060 121 Adjusting screw for brake Bowden cable 12 11 8 030 100 Contact-breaker kit 12 31 8 002 108 Socket cap screw for armature 12 12 5 590 014 Spark plug bakelit with BMW logo, unshielded 34 21 4 044 115 Wing nut for brake actuating rod “polished brass” 13 21 2 072 355 Throttle cable 35 21 4 044 218 Return spring for footbrake lever, V2A 13 12 2 072 255 Throttle cable 13 72 0 043 149 Air cleaner bolt 16 11 0 008 907 Tool compartment lid, painted black 35 21 4 044 220 Brake actuating rod incl.
bolt with leaf spring 46 52 4 028 002 Center stand 46 52 4 028 118 Spring for main stand 46 52 4 028 129 Bearing bush for main stand 46 54 5 096 200 Luggage bridge 46 61 0 035 303 Front wheel mudguard, primed 46 61 0 035 304 Front wheel mudguard, painted and coach-lined 46 61 5 090 116 Front wheel mudguard bracket, 18 inch 46 62 0 035 295 Rear wheel mudguard, primed 46 62 0 035 296 Rear wheel mudguard, painted and coach-lined 46 62 5 096 178 Registration number plate, black 46 71 1 235 428 Footrest rubber 16 11 0 009 950 Tank bearer (U-shaped) 16 11 4 080 137 Rubber cone for tank and exhaust bracket 16 11 4 080 194 Tank bearer 16 11 0 010 296 Bottom bow for tank mount 16 11 1 231 298 Tool compartment lid, primed 36 31 0 009 888 Thrust sleeve for wheel bearing left, one-piece hub 36 31 0 009 890 Thrust sleeve for wheel bearing, right 16 11 4 080 148 Rubber ring for tank/engine bracket, thin 16 11 4 080 160 Circlip for locking screw 36 31 0 009 891 Thrust sleeve for wheel bearing left, split hub 36 31 4 038 200 Spoke 127 x M 3.5, split hub 16 11 4 080 165 Locking screw for tool compartment lid 36 31 4 038 201 Spoke 127 x M 5, split hub 18 21 4 090 131 Spacer sleeve for silencer mount 18 21 4 090 143 Exhaust elbow holder 16 11 4 080 172 Square key for tool compartment lid 16 11 4 080 188 Seal for tool compartment lid 36 31 4 038 203 Spoke 212 x M 5, split hub 36 31 4 038 223 Spacer tube for wheel bearing 32 71 2 072 145 Clamping bolt for handlebar 32 71 2 072 147 Spacer sleeve for handlebar bracket 16 11 4 080 248 Rubber ring, thick, for tank bearer, top 36 31 4 038 240 Oil trap sleeve for wheel bearings 36 31 4 038 253 Felt washer capsule for wheel bearings 21 52 2 072 316 Clutch cable 36 31 4 038 258 Felt washer for wheel bearing sealing cap 36 31 4 038 270 Bearing cap on wheel hub 61 11 8 066 007 Wiring harness, front section 61 11 8 066 008 Wiring harness, rear section 23 11 1 012 112 Hexagon bolt M6 x 25 A/F 9, foot shift cap 23 21 1 030 120 Gearbox flange round nut M14 x 1.5 36 31 5 590 019 Spoke nipple M 5 36 31 5 590 021 Spoke 212 x M 3.5, split hub 51 14 0 035 269 Tank badge, domed 51 14 5 590 033 Lens head countersunk screw for tank badge M4 x 12 DIN 91 51 14 6 040 110 Tank badge rubber 51 25 0 035 314 Fuel cap, polished aluminium 23 22 1 030 128 Bushing for speedo shaft in the gearbox 62 12 8 080 020 “VDO” speedometer W = 1.00 0 –140 km/h for transmission ratio i = 25:6 23 31 0 028 482 Shift fork (1st + 2nd gear) 23 31 1 066 204 Shift fork (3rd + 4th gear) 46 52 0 005 310 Front stand for front wheel mudguard 46 52 0 005 311 Shouldered bolt for front stand on the side of the front 26 11 0 029 246 Hardy washer for universal shaft 46 52 0 006 605 Sidestand “narrow type” wheel mudguard 52 51 0 009 990 Spring assembly for rider’s saddle “VA polished” 52 51 0 009 991 “Pagusa” saddle cover with frame 52 51 0 009 992 “Pagusa” saddle cover without frame 52 51 7 002 009 Rider’s saddle assembly with VA spring and Pagusa cover, 10 mm bore 52 51 7 002 116 Saddle carrier, 10 mm bore 52 51 9 034 015 “Pagusa” pillion saddle for mounting on luggage rack 52 51 9 034 017 “Pagusa” pillion saddle for mounting on mudguard 52 53 9 034 021 “Schorsch Meier” dual seat 52 53 9 034 116 Side loop for dual seat 52 53 9 034 117 Side loop for dual seat Model-specific parts R 27 26 11 3 038 270 End bell for propshaft “polished aluminium” 46 52 0 009 941 Spring for main stand 46 61 0 005 312 Shouldered bolt for front stand in the centre of the front 11 25 0 000 630 Piston with rings and piston bolts 1st oversize 11 25 0 000 631 Piston with rings and piston bolts 2nd oversize 11 25 0 000 632 Piston with rings and piston bolts 3rd oversize 11 25 0 000 633 Piston with rings and piston bolts 4th oversize 11 81 4 034 126 Angle bracket, engine mount 31 41 0 027 245 Adjusting nut for steering-head bearing, bottom wheel mudguard 31 41 0 027 247 Thrust plate for steering damper 31 41 2 000 101 Lock nut for top of steerer 46 62 5 096 178 Registration number plate, black 46 71 1 235 428 Footrest rubber 31 41 2 000 184 Protective cap for steerer bearing 31 41 2 000 235 Friction-liner set for steering damper with rivets 51 14 0 035 269 Tank badge, domed 51 14 5 590 033 Lens head countersunk screw for tank badge M4 x 12 DIN 91 31 41 2 000 425 Oil seal for fork tube 31 42 0 009 855 Rubber seal for end cap for telescopic fork 12 11 8 030 155 Contact-breaker kit 31 42 2 000 182 Adjuster nut for steerer bearing, bottom 51 14 6 040 110 Tank badge rubber 61 12 0 027 307 Wiring loom, dipswitch to light (normal length + 8 cm) 61 12 0 027 308 Wiring loom for tail light in rear mudguard 61 12 8 060 113 Wiring loom, dipswitch to light, normal length 61 13 8 070 232 Cable clamp 61 21 8 042 109 Base for battery 61 21 8 042 140 Battery strap (short) 61 31 8 050 134 Washer for headlamp bracket 61 31 8 070 198 Rubber grommet for dipswitch 61 32 8 048 100 Ignition light switch 61 32 8 048 173 Connection plate 13 12 2 072 258 Throttle cable 13 72 0 043 147 Air cleaner bolt 31 42 2 000 408 “Pertinax” telescopic fork guide bushing 31 42 2 000 416 Clamping screw for fork guide 51 25 0 035 314 Fuel cap, polished aluminium 31 42 2 054 140 Sealing washer for shock-absorber tube, bottom 31 42 2 054 284 Washer beneath screw-in piece in fork 52 51 0 009 942 Saddle-mount screw 52 51 0 009 989 Rider’s saddle assembly with VA spring and Pagusa cover, 16 11 0 009 951 Tank bearer 16 11 4 080 137 Rubber cone for tank bracket 32 72 1 230 407 Rubber grip left, round 52 51 0 009 990 Spring assy.
for rider’s saddle “polished” 8 mm bore 18 21 4 090 141 Bracket for exhaust pipe 32 72 1 230 868 Rubber grip right, round 52 51 0 009 991 “Pagusa” saddle cover with frame 52 51 0 009 992 “Pagusa” saddle cover without frame 32 71 2 072 146 Clamping bolt for handlebar 32 72 2 072 217 Lever bolt, 12 mm head 52 51 0 009 993 Saddle carrier, 8 mm bore 61 11 8 066 009 Wiring harness, front section 61 11 8 066 010 Wiring harness, rear section 33 11 0 010 514 Sealing ring for end bell 33 11 3 038 170 Protective ring for propshaft, “dust boot, white” 52 51 9 034 015 “Pagusa” pillion saddle for mounting on luggage rack 52 51 9 034 017 “Pagusa” pillion saddle for mounting on mudguard 62 12 8 080 115 Sealing ring for speedometer 62 12 8 080 127 Speedo shaft 33 11 3 038 288 Cotter bolt for propshaft 52 53 9 034 021 “Schorsch Meier” dual seat 62 12 0 008 402 “VDO” speedometer W = 1.08 0 –140 km/h for transmission ratio i = 27:6 62 12 0 008 404 “VDO” speedometer W = 1.00 20 –140 km/h for transmission ratio i = 25:6 71 11 0 005 317 Original toolkit in linen tool-wrap 71 11 9 090 070 Tyre pump complete metal 36 37