BMW F 650 CS Repair Manual (EN)

Repair Manual

Issued by © BMW Motorrad After Sales UX-VS-2 All rights reserved. Not to be reprinted, translated or duplicated either wholly or in part without prior written permission. Errors and omissions excepted; subject to technical amendment. Printed in Germany 06/01

Стр. 2

Introduction

Introduction This Repair Manual will help you to perform all the main maintenance and repair work correctly and effi- ciently. If it is consulted regularly by workshop personnel it will form a useful addition to the theoretical and practical knowledge acquired at the BMW Training Centre. It is a contribution toward achieving even higher Service quality. A new issue of this repair manual will be published if amendments or additions (supplements) are needed.

All information in both text and illustrations refers to motorcycles in standard condition or with genuine BMW accessories installed, and not to motorcycles which have been modified in any way to depart from the manufacturer’s specification. • The Repair Manual is structured in the logical sequence of the work to be performed: Removal, Disas- sembling, Repair, Assembly, Installation. • The entire contents are divided into individual chapters, corresponding to the Construction Groups. 11 . 10 Chapter Page number within chapter If a reference is needed to a different page or chapter, an arrow symbol is shown followed by the chapter and page numbers, e. g. ( a 12.5).

• Work to be performed during an Inspection is described in Group “00”. The various inspection routines are numbered I, II, III and IV. This numbering is repeated in the work descriptions which follow, so that work can take place without interruption. • Use of the BMW special tools needed for certain tasks is described in the work instructions. If the need arises, repair instructions are also issued in the form of Service Information. This information is of course incorporated into the next issue of the Repair Manual. We also recommend, as an additional source of information, the Electronic Parts Catalogue (ETK), which contains clear and easy-to-follow illus- trations.

If the work described here is restricted to a particular equipment specification, for instance if a specific op- tional extra (OE) is fitted, this is stated in square brackets at the start of the item concerned, e.g. [Heated handlebar grips] . Please refer to the following pages as well for a description of other symbols used and how to work with them. BMW Motorrad After Sales Issued by BMW Motorrad After Sales UX-VS-2 D-80788 Mьnchen All rights reserved. Not to be reprinted, translated or duplicated either wholly or in part without prior written permission. Errors and omissions excepted; subject to technical amendment. Produced in Germany

Стр. 3

Activities

Use Each chapter starts with the list of contents. The list of contents is followed by the technical data table. Key to symbols In this Repair Manual for the F 650 CS model, the following symbols are used; their meanings are explained in the table. Special instructions aimed at improving the work procedures L Note: Special information on operating and inspecting the motorcycle as well as maintenance and adjustment procedures. e Attention: Instructions and precautions specifically intended to prevent damage to the motorcycle. Failure to comply with them could invalidate the warranty. d Warning:

This symbol stands for precautions and measures which are essential in order to protect the rider or other persons from possibly severe or fatal injury. Contents The titles of the tasks described in this chapter............. complete with page numbers Activities • Activities • The bullet symbol indicates work steps that are described in greater detail under another headline – Preceding activities – A line indicates work steps that are described in greater detail under another headline or in another chapter The term "remove" means that: the fastener (e.g. screw) must be backed off completely and removed or a component (e.g.

injection rail) has to be removed to the extent that components behind it (e.g. throttle valve rail) are rendered accessible The term "loosen" or "slacken" means that: the fastener (e.g. screw) must be backed off, but not removed X Tightening torque: Values are stated if they differ from DIN EN 24 014 or DIN 912 ISO industrial standards.

Стр. 4

Maintenance schedule

BMW Motorrad Maintenance schedule F 650 CS Customer Licence No. Mileage Job Order No. Date Mechanic’s signature BMW Inspection at 1,000 km/600 miles BMW Maintenance Service every 10,000 km/6,000 miles BMW Inspection every 20,000 km/ 12,000 miles BMW Annual Service Read the fault code memory with the BMW MoDiTeC Change the engine oil [engine only] while at regular operating temperature and replace the oil filter element Change the engine oil [engine and oil tank] while at regular operating temperature and replace the oil filter element if motorcycle is used only for short journeys or at outside temperatures below 0°C (32°F):

every 3 months or at the latest after 3,000 km (1,800 miles) Clean oil strainer in frame once only at 10,000 km/6,000 miles Check the coolant and restore to correct level if necessary Grease rubber grommets for cover insert Replace the coolant *) every 2 years Check valve clearances, adjust if necessary *) Replace the spark plug Drain the outlet hose from the air filter box Replace intake air filter If motorcycle is operated in very dirty or dusty conditions, clean or replace the intake air filter every 10,000 km (6,000 miles); check every 3,000 km (1,800 miles) Replace fuel filter every 40,000 km (24,000 miles) Check clutch play, adjust if necessary Examine brake pads and discs for wear, replace if necessary *) Check front/rear circuit brake fluid Check for operation of brake system and freedom from leaks; repair/replace if necessary *) Renew brake fluid at least once a year [ABS] Replace the primary front/rear brake master cylinder cup *) every 40,000 km (24,000 miles) Replace toothed belt Check toothed belt and sprocket, replace if necessary *) Check belt tension, adjust if necessary *) Check battery acid level, add distilled water if necessary Clean and grease the battery terminals, if necessary Check steering head bearings and adjust *) or replace if necessary *) Grease the side stand Using a torque wrench, check that the screws and nuts of the engine mounts, manifold fas- tener, the frame threaded fasteners, the rear-frame threaded fasteners, and the eccentric clamp are tightened to specified torque Final inspection with road safety and functional check:

– Clutch, gearshift – Steering – Front and rear brakes – Side stand contact switch – Condition of tyres and wheels, tyre pressures – Lights and signalling equipment, indicator and warning lights, instruments – Optional equipment – Test ride, if necessary *) Write up on separate invoice; Not part of standard service procedure UX-VS-2, 07.2001 BMW recommends Castrol

Стр. 5