AS Series Programming Manual _2 2-20 AS300 Series AS200 Series Latched Attribute Default OFF STOP RUN SM Function ON RUN STOP disabled or stops for Y0.2/axis 2 (Y0.2/Y0.3). *SM497 The output immediately stops when the instruction is disabled or stops for Y0.3. ○ ○ OFF OFF – N R/W OFF SM498 Change the target positon while outputting Y0.2/axis 2 (Y0.2/Y0.3) ○ ○ OFF OFF – N R/W OFF SM499 Change the target positon while outputting Y0.3 ○ ○ OFF OFF – N R/W OFF SM500 Outputting Y0.4/axis 3 (Y0.4/Y0.5). ○ ○ OFF OFF – N R OFF SM501 Y0.4/axis 3 (Y0.4/Y0.5) output is complete. ○ ○ OFF OFF – N R/W OFF SM502 Reversing the output direction of axis 3 (Y0.5).
○ ○ OFF OFF – N R/W OFF *SM503 Stopping the output of Y0.4/axis 3 (Y0.4/Y0.5). ○ ○ OFF OFF – N R/W OFF SM504 Enabling the positive maximum value for axis 3 (Y0.4/Y0.5). ○ ○ – – – Y R/W OFF SM505 Alarm: positive limit for axis 3 (Y0.4/Y0.5) ○ ○ OFF OFF – N R/W OFF SM506 Enabling the negative maximum value for axis 3 (Y0.4/Y0.5) ○ ○ – – – Y R/W OFF SM507 Alarm: negative limit for axis 3 (Y0.4/Y0.5) ○ ○ OFF OFF – N R/W OFF *SM508 Enabling the S curve ramp-up/down for axis 3 (Y0.4/Y0.5) ○ ○ OFF OFF – N R/W OFF SM509 Enabling fixed slope ramp-up/down for axis 3 (Y0.4/Y0.5) ○ ○ OFF OFF – N R/W OFF SM510 Auto-reset for Y0.4/axis 3 (Y0.4/Y0.5) output is complete.
○ ○ OFF OFF – N R/W OFF SM511 Executing an interrupt I502 when pulse output ends for axis 3 (Y0.4/Y0.5). ○ ○ OFF OFF – N R/W OFF SM512 Outputting Y0.5. ○ ○ OFF OFF – N R OFF SM513 Y0.5 output is complete. ○ ○ OFF OFF – N R/W OFF *SM514 Stopping the output of Y0.5. ○ ○ OFF OFF – N R/W OFF SM515 Auto-reset for Y0.5 output is complete. ○ ○ OFF OFF – N R/W OFF *SM516 Output immediately stops when the instruction is disabled or stops for Y0.4/axis 3 (Y0.4/Y0.5). ○ ○ OFF OFF – N R/W OFF *SM517 Output immediately stops when the instruction is disabled or stops for Y0.5.
○ ○ OFF OFF – N R/W OFF SM518 Change the target positon while outputting Y0.4/axis 3 (Y0.4/Y0.5) ○ ○ OFF OFF – N R/W OFF SM519 Change the target positon while outputting Y0.5 ○ ○ OFF OFF – N R/W OFF SM520 Outputting Y0.6/axis 4 (Y0.6/Y0.7). ○ ○ OFF OFF – N R OFF SM521 Y0.6/axis 4 (Y0.6/Y0.7) output is complete. ○ ○ OFF OFF – N R/W OFF SM522 Reversing the output direction of axis 4 (Y0.7) . ○ ○ OFF OFF – N R/W OFF *SM523 Stopping the output of Y0.6/axis 4 (Y0.6/Y0.7). ○ ○ OFF OFF – N R/W OFF SM524 Enabling the positive maximum value for axis 4 (Y0.6/Y0.7). ○ ○ – – – Y R/W OFF SM525 Alarm: positive limit for axis 4 (Y0.6/Y0.7).
○ ○ OFF OFF – N R/W OFF SM526 Enabling the negative maximum value for axis 4 (Y0.6/Y0.7). ○ ○ – – – Y R/W OFF SM527 Alarm: negative limit for axis 4 (Y0.6/Y0.7). ○ ○ OFF OFF – N R/W OFF