Atari Games Badlands Universal Kit — Atari Badlands Universal Kit Installation Instructions Manual PDF

Badlands Universal Kit Installation Notes to Table 1-3 Jamma Wire Connections TP ‘Twisted pair. 1, switched off. Then connect this. Awire to the NO, terminal on the external self-test switch. Connect the commpion terminal of the self-test. switch:to. one of the BK/W wires (GND). Connect four of the large BN wires ‘to the 5V- RTN (GND) ‘terminal on’ the. power supply unléss the power supply has a-12V RTN. If you have a 12V RIN, connect one of the wires to the 12V RTN Connect to the N.O. terminal of the left coin switch. ~ Connect the common terminal of the coin switch to one of the BK/W" wires. (GND) terminal. Three of the R wires. go to the +5V. terminal on the power supply.

If the power supply has a +SENSE terminal, connect one of ‘these three wires Connect to the switch: +SENSE instead of the +5V. The fourth wire goes to the red wires on the stéering assemblies. Connect both wires to the —5V terminal by balf) Connect. both wires to the +12V terminal of the power supply. Cf your coin counter(s). require(s) 12V, you can-use one of these two ‘wires for the:+ side of the coin counter(s).) Connect to the negative side of the coin counter(s). If your counter(s) require 5V, splice into: the ‘réed wire that brings +5V to the steering assemblies. See terminal of the right coin the common ‘terminal switch to oné of the BK/W : switches. Connect the common.

terminals switches to one of the BEK/AW: wires. : coin of the 11, Connect to the N.O. terminals of the ‘nent Fire/Start switches. Connect. the common terminals switches to one of the BK/W wires. - 42 Connect to the gray wire on the steering of the assembly: 13. Connect to the white wire on thesteering assembly, . Connect one wire to the negative sense terminal of the power supply Gf it exists). Connect the second wire to the common terminals: of the coin switches. the control switches. Connect the fourth wire to the black wires on the steering assembly harness. Note 2; above. Note: Do not use 24V counters. 15. Connect to the blue. wire on the pedal. Attach to the video display. 16.

Connect to the violet Use ‘this. wire if you want an external self-test switch..The Badlands kir already has: a~self=test switch on the PCB. If you*connect an external self- of the wires. 10. Connect to the N.O. terminals of the. left Fire/Stant of the power supply. Uf -5V is not available; connect: both: wires to:the 5.V RIN (GND) terminal on the power supply unless the power supply has 12V RTNo If it does; connect both wires to it, NOTE: If -5V is not used, the maximum power to the speaker is reduced to the NO. Connect wire on the pedal. _ Connect the brown wire to ‘the plus terminal on the speaker:-and the white wire to the negative terminal on the speaker. :

test switch; first make sure the switch on the PCB is If your original game used other voltages, they are not needed. Tie off any unused power supply. wires on the There is more than one wire for each voltage. Use more than one wire for each voltage (connecting them as described in Table 1-3) so that you do not overload the edge connector and cause it to burn. Connecting Video Display Wires NOTE The JAMMA harness provides only negative composite sync. If your video display requires separate positive sync, see Chapter 3 for alternative wiring. Connect the wires designated for the red, green and blue video guns along with the syne and ground wires, according to Table 1-3.

Connecting Coin Door Wires 1. Connect the wires on the JAMMA harness to the coin switches and meter according to Table 1-3. Connect one side of the door lamps to one of the BK/W wires. Connect the other side of the door lamps to the R wire supplying +5V to the joysticks. NOTE Do not use —5V for the coin door lamps. —5V is required for audio. (Some games have separate power supply outputs for the coin door lamps. If you choose to use these outputs, make sure you connect both sides of the lamps to the terminals on the power supply.) Connecting the Control Wires Connect the steering assembly harnesses and the button harnesses to the JAMMA harness according to the information in Table 1-3