TROUBLESHOOTING METHOD OF USING TROUBLESHOOTING CHARTS METHOD OF USING TROUBLESHOOTING CHARTS 1. Category of troubleshooting code number 2. Method of using troubleshooting table for each troubleshooting mode. a. Troubleshooting code number and problem. The title of the troubleshooting chart gives the trouble- shooting code, service code and failure mode (problem with the machine). (See example (1)) b. Distinguishing conditions. Even with the same failure mode (problem), the method of troubleshooting may differ according to the model, component, or problem.
In such cases, the failure mode (problem) is further divided into sections marked with small letters (for example, a), so go to the appropriate section to carry out troubleshooting. (See Example (3)) If the troubleshooting table is not divided into sections, start the troubleshooting from the first check item in the failure mode. c. method of following troubleshooting chart. (See Example (4)) i. Check or measure the item inside the left most box and, according to the answer, follow either the YES line or the NO line to go to the next condition box. (Note: The number at the top right corner of the condition box is an index number; it does not indicate the order to follow.) ii.
Following the YES or NO lines according to the results of the check or measurement will lead finally to the Cause column. Check the cause and take the action given in the Remedy column on the right. iii. Below the condition box, there are the methods of inspection or measurement, and the judgement values. If the judgement values below the condition box are correct or the answer to the question inside the condition box is YES, follow the YES line. If the judgement value is not correct, or the answer to the question in NO, then follow the NO line. iv. Below the condition box is given the preparatory work needed for inspection and measurement, and the judgement values.
If this preparatory work is neglected, or the method of operation or handling is mistaken, there is the danger that it may cause mistaken judgement or the equipment may be damaged. Therefore, before starting inspection of measurement, always read the instruc- tions carefully and start the work in order from the first item. d. When carrying out troubleshooting for the failure mode (problem), precautions that apply to all the items are given at the top of the page and marked with a # . (See Example (2)) The precautions marked # are not given in the condition box, but must always be followed then carrying out the check inside the condition box. e.
When carrying out troubleshooting, prepare the necessary troubleshooting tools. For details, see TOOLS FOR TESTING, ADJUSTING AND TROUBLESHOOTING. f. Installation position, pin number. A diagram or chart is given for the connector type, installation posi- tion, and connector pin number connection. When carrying out troubleshooting, see this chart for details of the connector pin number and location for inspection and measurement of the wiring connec- tor number appearing in the troubleshooting flow chart for each failure mode (problem). 20-94 TroubleshootingCodeNo.
Component Servicecode N-OO Troubleshootingofcommunicationabnormalitysystem E218group E-OO TTrroouubblleesshhoooottiinngg ooff eelleeccttrriiccaall ssyysstteemm ffoorr egnogvienren othrr,opttulem •p p ccoonnttrroolllleerr ((ggoovveerrnnoorr ccoonnttrrooll ssyysstteemm)) ump E3-OO group S-OO Troubleshootingofenginerelatedparts - C-OO TTrroouubblleesshhoooottiinngg ooff eelleeccttrriiccaall ssyysstteemm ffoorr egnogvienren othrr,optutlem •p p ccoonnttrroolllleerr ((ppuummpp ccoonnttrrooll ssyysstteemm)) E2-OO group F-OO TTrroouubblleesshhoooottiinngg ooff egnogvienren othr,roptutlem •p pcuomntpro clloenrtr ((iinnppuutt ssiiggnnaall ssyysstteemm)) oller - H-OO Troubleshootingofhydraulic,mechanicalsystem - M-OO Troubleshootingofmachinemonitor E1-OO group