Komatsu — eebm001902 a3.pdf

DISASSEMBLY AND ASSEMBLY CONTROL VALVE Assembly Coat the sliding surfaces of all parts with engine oil before installing. 1. Bucket control valve spool. a. Assemble spool assembly (29) to valve body. b. Assemble retainer (33) and spring (28), then fit O-ring to case (34) and install. Case mounting bolt: 30.87 ± 3.43 Nm (3.15 ± 0.35 kgm) c. Assemble retainer (32) and spring (31) to spool, then fit O-ring to case (30) and install. Case mounting bolt: 30.87 ± 3.43 Nm (3.15 ± 0.35 kgm) 2. Boom control valve spool a. Assemble spool assembly (54) to valve body. b. Assemble retainer (63) and spring (53), then fit O-ring to case (64) and install. Case mounting bolt:

30.87 ± 3.43 Nm (3.15 ± 0.35 kgm) c. Assemble spring (56) and piston (59), then install plug (58). Plug: 107.8 ± 14.7 Nm (11.0 ± 1.5 kgm) d. Assemble retainer (60) and spring (55), then install case (57). Case mounting bolt : 30.87 ± 3.43 Nm (3.15 ± 0.35 kgm) 3. R.H. travel, L.H. travel control valves. a. Assemble spool assembly (45) to valve body. b. Assemble retainer (49) and spring (44), then fit O-ring to case (50) and install. Case mounting bolt : 30.87 ± 3.43 Nm (3.15 ± 0.35 kgm) c. Assemble retainer (48) and spring (46) to spool, then fit O-ring to case (47) and install. Case mounting bolt : 30.87 ± 3.43 Nm (3.15 ± 0.35 kgm) 4. Swing control valve spool. a.

Assemble spool assembly (37) to valve body. b. Assemble retainer (42) and spring (36), then fit O-ring to case (43) and install. Case mounting bolt : 30.87 ± 3.43 Nm (3.15 ± 0.35 kgm) c. Assemble retainer (41) and spring (39), then fit O-ring to case (40) and install. Case mounting bolt : 30.87 ± 3.43 Nm (3.15 ± 0.35 kgm) 5. Arm control valve. a. Assemble spool assembly (68) to valve body. b. Assemble retainer (78) and spring (67), then fit O-ring to case (66) and install. Case mounting bolt : 30.87 ± 3.43 Nm (3.15 ± 0.35 kgm) c. Assemble retainer (69) and spring (74), then fit O-ring to case (70) and install. Case mounting bolt : 30.87 ± 3.43 Nm (3.15 ± 0.35 kgm) 6. Covers. a.

Fit O-ring to cover (16), then install. b. Fit O-ring to cover (9), then install. Mating surface of covers (16), (9): Seal end 242 or equivalent. # Tighten the mounting bolts in the order shown in the diagram on the right. Mounting bolt: 166.6 ± 9.8 Nm (17 ± 1 kgm) 7. LS shuttle valves, pump merge/divider valve, boom regeneration valve a. Assemble boom regeneration valve (62) and spring (61) to valve body, then install pump merge/divider valve assembly (80). # Tighten the mounting bolts in the order shown in the diagam on the right. Mounting bolt: 166.6 ± 9.8 Nm (17 ± 1 kgm) b. Install LS shuttle valves (81) and (79). Mounting bolt: 66.17 ± 7.35 Nm (6.75 ± 0.75 kgm) 30-96