daewoo — Daewoo Wheel Loader Shop Manual

Valve Adjustment Sequence Engine Cylinder Compression Test The valve clearance on a cold engine is 0.3 mm (0.012") for both intake and exhaust valves. Start the engine and allow it to operate long enough for normal warm-up. Allow a brief cool down period (for cylinder head temperature surge) and remove fuel injection nozzles from the head. Install the compression gauge adapter in each threaded nozzle hole, in succession, and crank the engine with the starter (200 RPM) testing compression in each cylinder, in turn. Measured compression should be between 24 kg/cm 2 Engine cylinder firing order is 1-5-3-6-2-4.

When valves of cylinder 6 are completely opened, number one cylinder is at top dead center. When valves of cylinder 1 are completely opened, number six cylinder is at top dead center. With No. 6 cylinder at TDC, adjust: Exhaust valves for No. 2, 4 and 6 cylinders Intake valves for No. 3, 5 and 6 cylinders With No. 1 cylinder at TDC, adjust: Exhaust valves for No. 1, 4 and 5 cylinders Intake valves for No. 1, 2 and 4 cylinders (340 psi) and 28 kg/cm 2 (398 psi), with a maximum difference between any two cylinders of 10 percent.

Wear Limits of Major Engine Components 8-2 ENGINE Mega 300-III Shop Manual Item Standard Value Limit (or NOTE) Pistons/Cylinder Cylinder liners Projected height Block head face, maximum distortion Cylinder head, height Valve seat depression, intake valves exhaust valves Piston diameter Piston/liner clearance Piston ring grooves, 1st ring 2nd ring Oil ring Piston height above block upper surface Piston ring gap, 1st ring 2nd ring Oil ring Piston ring installation note 123 mm – 123.025 mm (4.8425" – 4.8435") 0.03 mm – 0.08 mm (0.0012" – 0.0031") 0.05 mm (0.0020") 114.9 mm – 115.0 mm (4.5236" – 4.5276") 0.35 mm – 0.50 mm (0.0138" – 0.0197") 0.55 mm – 0.70 mm (0.0217" – 0.0276") 122.791 mm – 122.949 mm (4.8343" – 4.8405") 0.051 mm – 0.234 mm (0.0020" – 0.0092") 3.5 mm (0.1378") 3.060 mm – 3.080 mm (0.1205" – 0.1213") 4.040 mm – 4.060 mm (0.1591" – 0.1598") 0 mm – 0.12 mm (0" – 0.0047") 0.4 mm – 0.65 mm (0.0157" – 0.0256") 0.4 mm – 0.65 mm (0.0157" – 0.0256") 0.3 mm – 0.60 mm (0.0118" – 0.0236") Stagger gaps 120° apart.

123.225 mm (4.8514") Measured over 200 mm (7.9") 113.9 mm (4.484") 0.8 mm (0.031") 1.0 mm (0.039") Measured 18 mm (0.708") from bottom 0.3 mm (0.012") Replace if beyond limit Replace if beyond limit Replace if beyond limit 1.5 mm (0.0591") 1.5 mm (0.0591") 1.5 mm (0.0591") Ring gaps must not overlap. Space them as far apart as possible. (120° between each gap and the next.)