The Operator’s Cab Should Be Kept Clean, 1-11 Use Low Heat Portable Lighting, 1-11 Wear Eye Protection and Safety Clothing – Use Proper Tools, 1-11 Excavator Engine Specifications, 2-3 I Inspection and Maintenance, 3-4 Lubricating Grease Fittings, 3-4 Inspection and Maintenance, 3-4 Annually or Every 2,000 Operating Hours, 3-18 Bleeding Brakes, 3-18 Replace Hoses, 3-18 Daily or Every 10 Operating Hours, 3-7 Air Filter Indicator, 3-9 Antifreeze Protection Levels Table, 3-9 Check Coolant Level, 3-8 Check Engine Oil Level, 3-7 Check Hydraulic System Oil Level, 3-7 Check Transmission Oil Level, 3-7 Drain Fuel Condensation, 3-8 Refill Fuel, 3-8 Every 250 Operating Hours, 3-12 Change Engine Oil and Filter, 3-13 Clean Air Cleaner, 3-12 Hydraulic Full Flow Filter Replacement, 3-13 Hydraulic System Pilot Filter, 3-12 Replace Transmission Oil Filter, 3-13 Every 500 Operating Hours, 3-13 Fuel Filter Element Replacement, 3-13 Every 1,000 Operating Hours, 3-13 Center Axle and Axle End Oil Check, 3-13 Change Radiator Coolant, 3-17 Clean Fuel Tank and Strainer, 3-16 Drain and Replace Hydraulic Oil, 3-14 Drain and Replace Transmission Fluid, 3-15 Replace Air Cleaner Element, 3-17 Every 1,500 Operating Hours, 3-18 Center Axle and Axle End Oil Replacement, 3-18 Weekly or Every 50 Operating Hours, 3-10 Change Engine Oil and Filter, 3-10 Check Fan Belt Tension, 3-11 Clean Exterior of Radiator and Oil Cooler, 3-11 Hydraulic Full Flow Filter Replacement, 3-11 Replacing Transmission Oil Filters, 3-10 F Front and Rear Axles, 6-1 Front Axle Housing, 6-3 Fuel Injection Pump Installation, Alignment and Timing, 8-9 Injection Pump Delivery Volume, 8-10 Injection Pump Installation, 8-9 Injection Pump Timing Check, 8-10 G General Maintenance, 3-21 Check Battery Condition, 3-21 Fuel Transfer Pump, 3-21 Parking Brake Adjustment, 3-21 General Safety Essentials, 1-1 Accessory Applications, 1-1 Static Tipping Load, 1-1 General Specifications, 2-2 H Hydraulic Circuits and Components, 7-18 Bypass Valve, 7-22 Option Solenoid Valve, 7-21 Restriction Valve, 7-18 Unloading Valve, 7-19 Hydraulic Circuits Description, 7-1 Hydraulic Schematic, 7-1 Hydraulic Cylinders, 7-27 Boom Hydraulic Cylinder, 7-38 Bucket Hydraulic Cylinder, 7-39 Cylinder Assembly, 7-32 Cylinder Operation, 7-28 Hydraulic Cylinder Disassembly, 7-31 Hydraulic Cylinder Troubleshooting, 7-29 Hydraulic Pump, 7-3 Pilot Pump, 7-4 Pump Assembly, 7-11 Pump Disassembly, 7-5 Pump Installation, 7-17 Pump Removal, 7-4 Hydraulic System Schematic, 7-45 L Locations of Safety Labels, 1-2 Accumulator, 1-3 Keep Off the Steering Turn Area, 1-3 Stay Clear of Working Area Caution, 1-4 Warning for Battery Maintenance, 1-4 Warning for Handling Accumulator, 1-3 Warning for High Temperature Coolant, 1-3 Warning for High Temperature Hydraulic Oil, 1-3 Warning for Operation, Inspection and Maintenance, 1-2 10-2 INDEX Mega 300-III Shop Manual