99 7 SPN 6~ 7 SPN 6~ ...........continued TYPE SPN FMI En- gine Ma- chine type Description ECM 611 16 C F Fuel Inlet Meter Device : Fuel Inlet Meter Device - Data Valid but Above Normal Operational Range - Moderately Severe Level ECM 611 18 C F Fuel Inlet Meter Device :
Fuel Inlet Meter Device flow demand lower than expected - Data Val- id but Below Normal Operational Range - Moderately Severe Level ECM 612 2 C F Engine Speed/Position Sensor Circuit lost both of two signals from the magnetic pickup sen- sor - Data Erratic, Intermittent, or incorrect ECM 612 2 C E Engine Magnetic Speed/Posi- tion Lost Both of Two Signals - Data erratic, intermittent or in- correct ECM 612 2 C L Engine Magnetic Speed/Posi- tion Lost Both of Two Signals - Data erratic, intermittent or in- correct ECM 612 3 C F High voltage detected at the ICON lamp circuit when low voltage was expected by the ECM.
ECM 612 4 C F Less than 6 VDC (low voltage) detected at the ICON lamp cir- cuit when high voltage was ex- pected by the ECM. ECM 613 14 C F OEM Component Failure ECM 613 31 C F ECM 614 2 C F ECM 615 31 C F Incorrect voltage detected at the ICON starter relay/Interlock Cir- cuit input circuit by the ECM. TCU 62 * * L PTO TORQUE SIGNAL TCU 62 * * F PTO TORQUE SIGNAL ECM 620 1 C F ECM 620 18 C F OEM Sensor Supply Voltage Low - Warning ECM 620 3 C F High voltage detected on the in- ternal electronic control module (ECM) supply wire to the sen- sors. ECM 620 4 C F Low voltage detected on the in- ternal electronic control module (ECM) supply line to some of the sensors.
ECM 623 4 C E Red Stop Lamp Driver Circuit - Voltage Below Normal, or Shor- ted to Low Source ECM 623 4 C L Red Stop Lamp Driver Circuit - Voltage Below Normal, or Shor- ted to Low Source ECM 623 5 P E Red Stop Lamp : Current Below Normal ECM 623 5 P L Red Stop Lamp : Current Below Normal ECM 623 6 P E Red Stop Lamp : Current Above Normal ECM 623 6 P L Red Stop Lamp : Current Above Normal ECM 623 4 C F Red Stop Lamp : Red Stop Lamp Driver Circuit - Voltage Below Normal, or Shorted to Low Source ECM 623464 13 Y E Injector (No. 3 cylinder) correc- tion value error ECM 623464 13 Y L Injector (No. 3 cylinder) correc- tion value error continued..........
TYPE SPN FMI En- gine Ma- chine type Description TCU 6 * * E Short circuit in travel boost sole- noid system TCU 60 * * L ADDITIONAL BRAKE STATUS SIGNAL TCU 60 * * F ADDITIONAL BRAKE STATUS SIGNAL ECM 608 2 C F SAE J1587/J1922 data link - can not transmit. Communica- tion between the ECM and an- other device on the J1587/ J1922 data link has been lost. ECM 608 9 C F Data Communication error over the J1587 data link Circuit ECM 609 2 C F Engine Control Module Identifi- cation Input State Error ECM 609 2(J1587) C F Error detected in the control synchronization of multiple en- gines.
TCU 61 * * L AEB REQUEST SIGNAL TCU 61 * * F AEB REQUEST SIGNAL ECM 611 15 C F Turbocharger compressor outlet temperature - data above nor- mal. High turbocharger com- pressor outlet temperature has been calculated by the ECM. ECM 611 2 C F Auxiliary Intermediate (PTO) Speed Switch Validation - Data Erratic, Intermittent, or Incorrect. The position of the intermediate speed control switch 1 does not match the position of the inter- mediate speed control validation switch. ECM 611 31 C F Engine Control Module Data Lost - Condition Exits. Severe loss of data from the ECM.
ECM 611 4 C F Post-Filter Oil Pressure Sensor Circuit- Shorted Low ECM 611 16 C E Fuel Inlet Meter Device - Data Valid but Above Normal Opera- tional Range - Moderately Se- vere Level ECM 611 16 C L Fuel Inlet Meter Device - Data Valid but Above Normal Opera- tional Range - Moderately Se- vere Level ECM 611 18 C E Fuel Inlet Meter Device flow de- mand lower than expected - Da- ta Valid but Below Normal Op- erational Range - Moderately Severe Level ECM 611 18 C L Fuel Inlet Meter Device flow de- mand lower than expected - Da- ta Valid but Below Normal Op- erational Range - Moderately Severe Level ECM 611 31 C E Operator Interface Mode Transi- tion to Emergency Stop (Due to E-Stop) - Condition Exists ECM 611 31 C L Operator Interface Mode Transi- tion to Emergency Stop (Due to E-Stop) - Condition Exists ECM 611 2 C E Auxiliary Intermediate (PTO) Speed Switch Validation - Data erratic, intermittent or incorrect ECM 611 2 C L Auxiliary Intermediate (PTO) Speed Switch Validation - Data erratic, intermittent or incorrect ECM 611 3 C F High voltage detected at the alarm circuit when low voltage was expected by the ECM.
ECM 611 7 C F Autoshift failure, at least three shift attempts were missed. continued..........