100 7 SPN 6~ ...........continued TYPE SPN FMI En- gine Ma- chine type Description ECM 623465 13 Y E Injector (No. 4 cylinder) correc- tion value error ECM 623465 13 Y L Injector (No. 4 cylinder) correc- tion value error ECM 624 5 P E Amber Warning Lamp : Current Below Normal ECM 624 5 P L Amber Warning Lamp : Current Below Normal ECM 624 6 P E Amber Warning Lamp : Current Above Normal ECM 624 6 P L Amber Warning Lamp :
Current Above Normal ECM 625 9 C F Proprietary Datalink Error (OEM/Vehicle Datalink) - Abnor- mal update rate ECM 625 9 C E Proprietary Datalink Error (OEM/Vehicle Datalink) - Abnor- mal update rate ECM 625 9 C L Proprietary Datalink Error (OEM/Vehicle Datalink) - Abnor- mal update rate ECM 625 2 C F Komnet Datalink Cannot Trans- mit - Data Erratic, Intermittent, or Incorrect. Communications within the OEM datalink network is intermittent.
ECM 626 1 C F Start Assist Device - Canister Empty (Ether Injection) ECM 626 18 C F Start Enable Device 1 Canister Empty (Ether Injection) - Data Valid But Below Normal Operat- ing Range ECM 626 3 C F Start Enable Device 1 Circuit (Ether Injection) - Voltage above normal, or shorted to high source ECM 626 4 C F Start Enable Device 1Circuit (Ether Injection) - Voltage below normal, or shorted to low source ECM 626 18 C E Start Enable Device 1 Canister Empty (Ether Injection) - Data Valid But Below Normal Operat- ing Range ECM 626 18 C L Start Enable Device 1 Canister Empty (Ether Injection) - Data Valid But Below Normal Operat- ing Range ECM 626 3 C E Start Enable Device 1 Circuit (Ether Injection) - Voltage above normal, or shorted to high source ECM 626 3 C L Start Enable Device 1 Circuit (Ether Injection) - Voltage above normal, or shorted to high source ECM 626 4 C E Start Enable Device 1Circuit (Ether Injection) - Voltage below normal, or shorted to low source ECM 626 4 C L Start Enable Device 1Circuit (Ether Injection) - Voltage below normal, or shorted to low source ECM 626 5 P E Engine Start Enable Device 1 :
Current Below Normal ECM 626 5 P L Engine Start Enable Device 1 : Current Below Normal ECM 626 6 P E Engine Start Enable Device 1 : Current Above Normal ECM 626 6 P L Engine Start Enable Device 1 : Current Above Normal ECM 626 11 C F Start Assist Device Control Cir- cuit Error (Ether Injection) ECM 627 12 C F Injector Power Supply - Bad In- telligent Device or Component continued..........
...........continued TYPE SPN FMI En- gine Ma- chine type Description ECM 627 12 C E Injector Power Supply - Bad in- telligent device or component ECM 627 12 C L Injector Power Supply - Bad in- telligent device or component ECM 627 2 C E Power Supply Lost With Ignition On - Data Erratic, Intermittent, or Incorrect ECM 627 2 C L Power Supply Lost With Ignition On - Data Erratic, Intermittent, or Incorrect ECM 627 2 C F Power Supply : Power Lost With Ignition On - Data Erratic, Inter- mittent, or Incorrect ECM 628 9 C F Proprietary Datalink Error (OEM/Vehicle Datalink) Abnor- mal Update Rate. The ECM cannot communicate with the immobilizer anti-theft system.
ECM 629 31 C F At Least One Unacknowledged Most Severe Fault - Condition Exists ECM 629 12 C E Engine Control Module Critical Internal Failure - Bad intelligent device or component ECM 629 12 C L Engine Control Module Critical Internal Failure - Bad intelligent device or component ECM 629 12 C F Engine Control Module Warning Internal Hardware Failure - Bad intelligent device or component ECM 629 31 C E At Least One Unacknowledged Moderately Severe Fault - Con- dition Exists ECM 629 31 C L At Least One Unacknowledged Moderately Severe Fault - Con- dition Exists ECM 629 2 C F Fuel Pump Control Module, Electronic Calibration Code Er- ror ECM 629 9 C F The ECM expected information from a multiplexed device but did not receive it soon enough, or did not receive it at all.
TCU 63 * * L DRIVING MODE SIGNAL TCU 63 * * F DRIVING MODE SIGNAL ECM 630 12 Y E EEPROM memory deletion error ECM 630 12 Y L EEPROM memory deletion error ECM 630 13 C F Engine Control Module – out of calibration ECM 630 12 C E Engine Control Module Calibra- tion Memory - Bad intelligent de- vice or component ECM 630 12 C L Engine Control Module Calibra- tion Memory - Bad intelligent de- vice or component ECM 630 13 C E Electronic Calibration Code In- compatibility - Out of Calibration ECM 630 13 C L Electronic Calibration Code In- compatibility - Out of Calibration ECM 630 31 C E ECM Program Memory (RAM) Corruption - Condition Exists ECM 630 31 C L ECM Program Memory (RAM) Corruption - Condition Exists ECM 630 12 C F Engine Control Module - Warn- ing Software error ECM 630 2 C F Calibration Memory :
Engine Control Module data lost - Data Erratic, Intermittent, or Incorrect ECM 630 2 P E Calibration Memory: Erratic, In- termittent, or Incorrect continued..........