Cummins — Cummins Engine Error Codes Manual for Hyundai Construction Equipment

81 6 SPN 5~ ...........continued TYPE SPN FMI En- gine Ma- chine type Description TCU 51 * * L FMR2 TIMEOUT ECM 51 0 S F The position of the valve used to reg- ulate the supply of a fluid, usually air or fuel/air mixture, to an engine. ECM 51 1 S F The position of the valve used to reg- ulate the supply of a fluid, usually air or fuel/air mixture, to an engine. ECM 51 2 S F The position of the valve used to reg- ulate the supply of a fluid, usually air or fuel/air mixture, to an engine. ECM 51 3 S F The position of the valve used to reg- ulate the supply of a fluid, usually air or fuel/air mixture, to an engine.

ECM 51 4 S F The position of the valve used to reg- ulate the supply of a fluid, usually air or fuel/air mixture, to an engine. ECM 51 5 S F The position of the valve used to reg- ulate the supply of a fluid, usually air or fuel/air mixture, to an engine.

ECM 51 7 S F Throttle Position Sensor, not plausi- ble ECM 51 7 S E Throttle Position Sensor, not plausi- ble ECM 51 8 S F Endpoints of throttle position sensor are out of range ECM 51 7 S L Throttle Position Sensor, not plausi- ble ECM 51 8 S E Endpoints of throttle position sensor are out of range ECM 51 9 S F Throttle Position Sensor, correlation error ECM 51 8 S L Endpoints of throttle position sensor are out of range ECM 51 9 S E Throttle Position Sensor, correlation error ECM 51 9 S L Throttle Position Sensor, correlation error TCU 51 * * F FMR2 TIMEOUT MCU 5110 3 * L S.C. TO BATTERY VOLTAGE OR O.C.

AT TRANSMISSION SUMP TEMPERATURE SENSOR INPUT - the measured voltage is too high MCU 5110 4 * L S.C. TO GROUND AT TRANSMIS- SION SUMP TEMPERATURE SEN- SOR INPUT - the measured voltage is too low MCU 5120 3 * L S.C. TO BATTERY VOLTAGE OR O.C. AT RETARDER / TORQUE- CONVERTER TEMPERATURE SENSOR INPUT - the measured voltage is too high MCU 5120 4 * L S.C.

TO GROUND AT RETARDER / TORQUECONVERTER TEMPERA- TURE SENSOR INPUT - the meas- ured voltage is too low ECM 5125 3 C F Sensor Supply 7 Circuit - Voltage above normal, or shorted to high source ECM 5125 4 C F Sensor Supply 7 Circuit - Voltage be- low normal, or shorted to low source ECM 5125 3 C E Sensor Supply 7 Circuit - Voltage above normal, or shorted to high source ECM 5125 3 C L Sensor Supply 7 Circuit - Voltage above normal, or shorted to high source ECM 5125 4 C E Sensor Supply 7 Circuit - Voltage be- low normal, or shorted to low source ECM 5125 4 C L Sensor Supply 7 Circuit - Voltage be- low normal, or shorted to low source ECM 513 4 C F Engine Brake Driver #1 Circuit - shorted low continued..........

...........continued TYPE SPN FMI En- gine Ma- chine type Description MCU 514 4 * E Parking Relay-Voltage Below Nor- mal, Or Shorted To Low Source MCU 514 4 * L Parking Relay-Voltage Below Nor- mal, Or Shorted To Low Source MCU 514 6 * E Parking Relay-Current Above Normal Or Grounded Circuit MCU 514 6 * L Parking Relay-Current Above Normal Or Grounded Circuit MCU 5140 12 * L LOGICAL ERROR AT ENGINE SPEED INPUT TCU measures a en- gine speed over a threshold and the next moment the measured speed is zero MCU 5140 3 * L S.C. TO BATTERY VOLTAGE OR O.C. AT ENGINE SPEED INPUT TCU measures a voltage higher than 7.00 V at speed input pin MCU 5140 4 * L S.C.

TO GROUND AT ENGINE SPEED INPUT TCU measures a voltage less than 0.45V at speed in- put pin MCU 5150 12 * L LOGICAL ERROR AT TURBINE SPEED INPUT TCU measures a tur- bine speed over a threshold and at the next moment the measured speed is zero MCU 5150 3 * L S.C. TO BATTERY VOLTAGE OR O.C. AT TURBINE SPEED INPUT TCU measures a voltage higher than 7.00V at speed input pin MCU 5150 4 * L S.C. TO GROUND AT TURBINE SPEED INPUT TCU measures a voltage less than 0.45V at speed in- put pin MCU 5160 12 * L LOGICAL ERROR AT INTERNAL SPEED INPUT TCU measures a in- ternal speed over a threshold and at the next moment the measured speed is zero MCU 5160 3 * L S.C. TO BATTERY VOLTAGE OR O.C.

AT INTERNAL SPEED INPUT TCU measures a voltage higher than 7.00V at speed input pin MCU 5160 4 * L S.C. TO GROUND AT INTERNAL SPEED INPUT TCU measures a voltage less than 0.45V at speed in- put pin MCU 517 4 * E Traveling Cutoff Relay-Voltage Be- low Normal, Or Shorted To Low Source MCU 517 4 * L Traveling Cutoff Relay-Voltage Be- low Normal, Or Shorted To Low Source MCU 517 6 * E Traveling Cutoff Relay-Current Above Normal Or Grounded Circuit MCU 517 6 * L Traveling Cutoff Relay-Current Above Normal Or Grounded Circuit MCU 5170 12 * L LOGICAL ERROR AT OUTPUT SPEED INPUT TCU measures a out- put speed over a threshold and at the next moment the measured speed is zero MCU 5170 3 * L S.C.

TO BATTERY VOLTAGE OR O.C. AT OUTPUT SPEED INPUT TCU measures a voltage higher than 12.5V at speed input pin MCU 5170 4 * L S.C. TO GROUND AT OUTPUT SPEED INPUT TCU measures a voltage less than 1.00V at speed in- put pin MCU 5180 2 * L OUTPUT SPEED ZERO DOESN’T FIT TO OTHER SPEED SIGNALS if transmission is not neutral and the shifting has finished, TCU measures outputspeed zero and turbine speed or internal speed not equal to zero. continued..........