Mitsubishi SA6D125 — FUEL INJECTION PUMP CALIBRATION DATA

TESTING AND ADJUSTING FUEL SYSTEM (CALIBRATION DATA) 615002 12-12-6 8 12-12-6 (10) Injection Pump Assembly Number Applicable Machine Applicable Engine 6151-72-1790 (106692-9350) Model Serial No. Model Serial No. 6151-72-1791 (106692-9352) ( ): Injection pump manufacturer’s part No.

LW250-5 S6D125-2 Injection Injection pump Pump Type Manufacturer PE-P(PS3000) BOSCH Injection pump specification Engine Specification Rotating direction Counterclockwise Flywheel horsepower (kW {HP}) / rpm) 184 {250}/2,100 (Gross) Injection order 1 – 5 – 3 – 6 – 2 – 4 Maximum torque (Nm {kgm}/ rpm) 1,100 {112}/1,400 (Gross) Injection interval 59°30’ – 60°30’ High idling speed (rpm) 2,300 – 2,400 Plunger pre-stroke (mm) 3.70 – 3.80 Low idling speed (rpm) 550 – 650 Delivery valve (mm3/st) 90 Pump tester capacity retraction volume Motor 7.5 kW for Service standard Calibration Standard ( ): Injection pump manufacturer’s part number Applicable Machine Applicable Engine Model Serial No.

Model Serial No. LW250-5 S6D125-2 Conditions Nozzle & nozzle holder part No Nozzle part No. ‡ Service standard indicates data Nozzle holder part No. using calibration Injection pipe (m test parts. (Outside dia. x inside dia. x length) ‡ Manufacturer Test oil standard is data Oil temperature (° for factory test. Nozzle opening pressure (MPa{kg/cm2 Transfer pump pressure (kPa{kg/cm2 Service standard Manufacturer standard Nozzle & nozzle holder part No . (105780-8140) 6151-12-3400 (105111-4600) Nozzle part No. (105780-0000) 6151-12-3420 (105025-0750) Nozzle holder part No. (105780-2080) 6152-12-3110 (105041-7130) Injection pipe (m (Outside dia. x inside dia.

x length) m) 8 x 3 x 600 6 x 2.2 x 720 Test oil ASTM D975 No. 2 diesel fuel or equivalent Oil temperature (° C) 40 to 45 Nozzle opening pressure (MPa{kg/cm2 }) 17.2 {175} 24.5 {250} Transfer pump pressure (kPa{kg/cm2 }) 157 {1.6} 157 {1.6} Injection volume ‡ Rack positions B to E are the reference volume when adjusting the injection volume. ‡ Marks fl are average volumes.

Rack p point ( Rack Pump osition speed mm) (rpm) Service standard (cc/ st.) Maximum Injection variance volume between cylinde Manufacturer standard (cc/1000 st.) Maximum variance between cylinde Injection r volume bet Maximum variance ween cylinder A (Basic point) 9.0 1,050 fl125 ± 2 ±3 fl147.5 – B 9.0 700 fl147 ± 2 – fl161.5 – C app rox.

6.3 300 fl14 ± 1.5 ±15 fl15 – D – – – – – – E – 100 fl145+20 +0 – fl150 – Governor performance curve Boost compensator performance curve Injection Pump Type Injection pum Manufacture PE-P(PS3000) BOSCH Rotating direction Counterclockwise Injection order 1 – 5 – 3 – 6 – 2 – 4 Injection interval 59°30’ – 60°30’ Plunger pre-stroke (mm) 3.70 – 3.80 Delivery valve (mm3/st) retraction volume 90