Mitsubishi SA6D125 — FUEL INJECTION PUMP CALIBRATION DATA

TESTING AND ADJUSTING FUEL SYSTEM (CALIBRATION DATA) 615002 12-12-5 8 12-12-5 (10) Injection Pump Assembly Number Applicable Machine Applicable Engine 6151-72-1640 (106692-9320) 6151-72-1641 (106692-9323) Model Serial No. Model Serial No. ( ): Injection pump manufacturer’s part No.

D75S-5 S6D125-2 Injection Injection pump Pump Type Manufacturer PE-P(PS3S) BOSCH Injection pump specification Engine Specification Rotating direction Counterclockwise Flywheel horsepower (kW {HP}) / rpm) 166 {222}/2,000 (Gross) Injection order 1 – 5 – 3 – 6 – 2 – 4 Maximum torque (Nm {kgm}/ rpm) 963 {98.2}/1,500 (Gross) Injection interval 59°30’ – 60°30’ High idling speed (rpm) 2,150 – 2,250 Plunger pre-stroke (mm) 3.70 – 3.80 Low idling speed (rpm) 550 – 650 Delivery valve (mm3/st) 90 Pump tester capacity retraction volume Motor 7.5 kW for Service standard Calibration Standard ( ): Injection pump manufacturer’s part number Applicable Engine Serial No. Model Serial No.

S6D125-2 Conditions Nozzle & nozzle holder part N Nozzle part No. ‡ Service standard indicates data Nozzle holder part No. using calibration Injection pipe (m test parts. (Outside dia. x inside dia. x length ‡ Manufacturer Test oil standard is data Oil temperature ( for factory test. Nozzle opening pressure (MPa{kg/cm Transfer pump pressure (kPa{kg/cm Service standard Manufacturer standard Nozzle & nozzle holder part N o. (105780-8140) 6151-12-3400 (105111-4600) Nozzle part No. (105780-0000) 6151-12-3420 (105025-0750) Nozzle holder part No. (105780-2080) 6152-12-3110 (105041-7130) Injection pipe (m (Outside dia. x inside dia. x length m) 8 x 3 x 600 ) 6 x 2.2 x 720 Test oil ASTM D975 No.

2 diesel fuel or equivalent Oil temperature ( °C) 40 to 45 Nozzle opening pressure (MPa{kg/cm 2}) 17.2 {175} 24.5 {250} Transfer pump pressure (kPa{kg/cm 2}) 157 {1.6} 157 {1.6} Injection volume ‡ Rack positions B to E are the reference volume when adjusting the injection volume. ‡ Marks fl are average volumes.

Rack poin Rack Pump position speed t (mm) (rpm) Service standard (cc/ st.) Maximum Injection variance volume between cylinder Manufacturer standard (cc/1000 st.) Maximum variance between cylinder Injection volume Maximum variance between cylinder A (Basic p 8.0 1,000 oint) – – fl128 – 132 ±3 B 8.5 750 – – fl150 – 154 ±4 C 6.1 300 – – fl13.5 – 16.5 ±15 D 10.7 – 10.9 100 – – – – E 7.7 1,050 – – fl119 – 125 – Governor performance curve Boost compensator performance curve Injection Pump Type Injection pump Manufacturer PE-P(PS3S) BOSCH Rotating direction Counterclockw Injection order 1 – 5 – 3 – 6 – 2 Injection interval 59°30’ – 60°3 Plunger pre-stroke (mm ) 3.70 – 3.80 Delivery valve (mm3/st retraction volume ) 90