Komatsu — At The Truck - Ground Level Walk Around Inspection

OM3038 8/03 Operating Instructions - Section 30 Page 30-3 7. Move in behind the front wheel, and inspect the steering cylinder. Check the greasing and attaching hard- ware. Check suspension attaching hardware and suspension extension. Be sure the suspension protective boot is in good condition. Inspect the hub and brakes for any unusual conditions. Check entire area for leaks. 8. Inspect sight glass on hydraulic tank. With engine stopped and body down, hydraulic fluid must be visible in upper sight glass. 9. Move around the hydraulic tank and in front of the rear dual tires; inspect the hoist cylinder for any damage and leaks.

Inspect both upper and lower hoist cylinder pins for security, and for proper greasing. 10. Before leaving this position, look under the lower edge of the chassis to be sure the flexible duct that carries the air from the main blower to the final drive housing is in good condition with no holes or breakage. Also look up at the main hydraulic pumps to see that there is no leakage or any other unusual condition with pumps or pump drive shafts. 11. Move on around the dual tires, check to see that all wheel nuts/studs are in place and tight. Inspect wheel for any oil that would indicate brake leakage or wheel motor leakage. Check dual tires for cuts, damage or bubbles.

Verify that inflation appears to be correct. If the truck has been run on a "flat", the tire must be cooled before moving the truck inside . Check for any rocks that might be lodged between dual tires. Check rock ejector condition and straightness (so that it can not damage a tire). 12. Inspect left rear suspension for damage and for correct rod exposure. Check for leaks. Ensure that the covers over the chrome piston rod are in good condition and inspect for proper greasing. 13. Open rear hatch cover. Inspect for leaks around the parking brakes. Inspect condition of cooling air exhaust ductwork to be certain that it is intact and that there are no obstructions. 14.

While standing in front of the rear hatch, look up to see that rear lights are in good condition, along with the back-up horns. Look up at panhard rod to see that it is getting proper greasing. Also look at both body hinge pins for greasing and any abnormal condition. Check hoist limit switch and clear any mud/debris from con- tacts. 15. Perform the same inspection on the right rear suspension as done on the left. 16. Move around the right dual tires; inspect between the tires for rocks, and check condition of the rock ejector. Inspect the tires for cuts or damage, and for correct inflation. 17.

Perform the same inspection for wheel nuts/studs and wheel leaks that was done on the left hand dual wheels. 18. Move in front of right dual tires, and inspect the hoist cylinder in the same manner as the left side. Check security and condition of body-up limit switch. Remove any mud/dirt accumulation from switch. 19. Move around the fuel tank. Inspect the fuel quantity gauge, (this should agree with what will show on the gauge in the cab). Inspect the attaching hardware for the fuel tank at the upper saddles, and then at the lower back of the tank for the security and condition of the mounts. Check hoist filters for leaks. 20.

Move in behind the right front wheel, and inspect the steering cylinder. Check the greasing and attaching hardware. Check suspension attaching hardware and suspension extension. Be sure the suspension protec- tive boot is in good condition. Inspect the hub and brakes for any unusual conditions. Check entire area for leaks. 21. Move out and around the right front wheel; inspect that all wheel nuts/studs are in place and tight. 22. Move in behind the front of the right front wheel, check hub and brakes for leaks and any unusual condition. Inspect steering cylinder for security and for proper greasing. Inspect the engine compartment for any leaks and unusual conditions.

Inspect the fan guard and belts. Check for any rags or debris behind radiator. 23. Inspect auto lube system. See Automatic Lubrication System in Section 42, for specific details concerning the auto lube system. 24. Move around to the right front of the truck, drop the air cleaner pans to remove dirt, latch up, and secure. Inspect battery box cover for damage and be sure it is in place and secure. 25. As you move in front of the radiator, inspect for any debris that might be stuck in front of the radiator and remove it. Check for any coolant leaks. Inspect headlights and fog lights.