Komatsu — Retard Speed Control (RSC) Adjust Dial

Operator Cab And Controls - Section 32 OM3202 Page 32-8 Override/Fault Reset Switch This push-button switch (9, Figure 32-3) is spring- loaded to the OFF position. When pushed in and held, this switch may be used for several functions. Retard Speed Control (RSC) Adjust Dial RSC adjust dial (12, Figure 32-3) allows the operator to vary the downhill truck speed that the retard speed control system will maintain when descending a grade. This function can be overridden by either the accelerator, retard lever, or retard pedal. When the dial is rotated counterclockwise toward this symbol, the truck will descend a grade at lower speeds. 1.

This switch permits the operator to override the body-up limit switch and move the truck forward when the selector switch is in FORWARD, the dump body is raised, and the brakes are released. When the dial is rotated clockwise toward this symbol, the truck speed will increase. Use of the override switch for this purpose is intended for emergency situations only! ALWAYS refer to the grade/speed retard chart in the operator's cab , and follow the recommenda- tions for truck operation. DO NOT exceed these rec- ommended MAXIMUM speeds when descending grades with a loaded truck. 2. The push button deactivates the retard pedal function when speed of truck is below 3 mph (4.8 kph). 3.

The override switch is also used to reset an electric system fault when indicated by a red warning light (Refer to Overhead Status/Warn- ing Indicators in this section. Throttle pedal position will override RSC setting. If operator depresses throttle pedal to increase truck speed, dynamic retarding will not come on unless truck overspeed setting is reached or foot operated retard pedal is used. When throttle pedal is released and RSC switch is on, dynamic retarding will come by either the . se nd rd e. tard chart in on at, or above, the RSC 10, Figure 32-3 - Blank truck speed to, and maint This position is not used for the To adjust RSC control, p 930E.

with dial (12) rotated towa ing truck at desired maxi pedal to let truck coast a In some other truck models, this posi- slowly counterclockwise tion is used for an engine idle switch. activated. Dynamic retar automatically anytime the RSC switch is on, and thr With RSC switch on and will function as follows: A the "set" speed and thrott Retard Speed Control (RSC) Switch retarding will apply. As tr Retard speed control switch (11, Figure 32-3) turns the amount of retarding ef the system on and off. Push the knob in for OFF and to keep the selected s pull the knob out to turn the system ON. decreases, the retarding the selected speed.

If “IN” “OFF” decrease to approximate "set" speed, dynamic reta cally. If truck speed mu operator can turn the adj “OUT” “ON” depress the foot operated If the operator depresse pedal and the retard effo that from the automatic s will override RSC. on at, or above, the truck speed to, and for the To adjust RSC cont with dial (12) rotate ing truck at desired pedal to let truck c els, this posi- slowly counterclock idle switch. activated. Dynamic automatically anytim RSC switch is on, a With RSC switch o will function as follo the "set" speed and RSC) Switch retarding will apply. itch (11, Figure 32-3) turns the amount of retard ush the knob in for OFF and to keep the selec he system ON.

decreases, the reta the selected spee “IN” “OFF” decrease to appro "set" speed, dynam RSC maint rol, p d towa maxi sys tem ON. d th “IN” “OFF” d "s N. d th ” “OFF” d "s ecreases, e selecte ecrease t et" speed ” “O “O FF” “IN ” ally. If tru c o d If perator ca epress the the oper n a ON” “OU T p edal and t r the , this posi- with ing t is posi - witch.