Standard bolt tightening torque table Others : 1. The above torque rating have been determined to 70% or so of the limit value for bolt elasticity. 2. Tension is calculated by multiplying tensile strength by cross section of thread. 3. Special screws should be tightened to 85% or so of the standard value. For example, a screw coated with MoS 2 should be tightened to 60% or so of the standard value. z Tightening torque for plug screw Refer to the following table for bolts other then described above z Tightening torque for hollow screw(4-hole) * :
Adopted in DOOSAN engine DL06 Diesel Engine Special Tool List 195 Diameter x pitch (mm) Degree of strength 3.6 4.6 4.8 5.6 5.8 6.6 6.8 6.9 8.8 10.9 12.9 (4A) (4D) (4S) (5D) (5S) (6D) (6S) (6G) (8G) (10K) (12K) Limit value for elasticity (kg/mm2) 20 24 32 30 40 36 48 54 64 90 108 Tightening torque (kg.m) M5 0.15 0.16 0.25 0.22 0.31 0.28 0.43 0.48 0.5 0.75 0.9 M6 0.28 0.30 0.45 0.4 0.55 0.47 0.77 0.85 0.9 1.25 0.5 M7 0.43 0.46 0.7 0.63 0.83 0.78 1.2 1.3 1.4 1.95 2.35 M8 0.7 0.75 1.1 1 1.4 1.25 1.9 2.1 2.2 3.1 3.8 M8x1 0.73 0.8 1.2 1.1 1.5 1.34 2.1 2.3 2.4 3.35 4.1 M10 1.35 1.4 2.2 1.9 2.7 2.35 3.7 4.2 4.4 6.2 7.4 M10x1 1.5 1.6 2.5 2.1 3.1 2.8 4.3 4.9 5 7 8.4 M12 2.4 2.5 3.7 3.3 4.7 4.2 6.3 7.2 7.5 10.5 12.5 M12x1.5 2.55 2.7 4 3.5 5 4.6 6.8 7.7 8 11.2 13.4 M14 3.7 3.9 6 5.2 7.5 7 10 11.5 12 17 20 M14x1.5 4.1 4.3 6.6 5.7 8.3 7.5 11.1 12.5 13 18.5 22 M16 5.6 6 9 8 11.5 10.5 17.9 18.5 18 26 31 M16x1.5 6.2 6.5 9.7 8.6 12.5 11.3 17 19.5 20 28 33 M18 7.8 8.3 12.5 11 16 14.5 21 24.2 25 36 43 M18x1.5 9.1 9.5 14.5 12.5 18.5 16.7 24.5 27.5 28 41 49 M20 11.5 12 18 16 22 19 31.5 35 36 51 60 M20x1.5 12.8 13.5 20.5 18 25 22.5 35 39.5 41 58 68 M22 15.5 16 24.5 21 30 26 42 46 49 67 75 M22x1.5 17 18.5 28 24 34 29 47 52 56 75 85 M24 20.5 21.5 33 27 40 34 55 58 63 82 92 M24x1.5 23 25 37 31 45 38 61 67 74 93 103 M10 M12 M14 M16 M18 M22 M24 M26 M30 5.0 5.0 8.0 8.0 10.0 10.0 12.0 12.0 15.0 M8 M10 M12 M14 M16 M18 M22 M26 M30 M38 SM25C - 1.6 2.5 3.5 4.5 5.5 9.0 13.0 18.0 30.0 * SUM22L 0.8 1.8 3.0 4.0 5.5 6.5 11.0 16.0 20.0 35.0 STS304 0.8 1.8 3.0 4.0 5.5 6.5 11.0 16.0 20.0 35.0