Komatsu — WHEN REQUIRED

. MAINTENANCE SERVICE PROCEDURE WARNING 4 - 22 When deciding th e ratio of antifreeze to water, ch eck the lowest temperature in the past, and decide from the mixi table given below . r to estimate and temperature about 10°C (18°F) lower when deciding the mixing ratio. depends on the ambient temperature, but it should always be a minimum of 30% by volu mount of coolant x 100). It is actually bette r to estimate and temperature about 10°C (18°F) lowe r when deciding th The mixing ratio depends on the ambient temp mount of coolant x 100). (antifreeze/total a The freezing temp erature of undiluted antifreeze is -15°C (5°F).

Do not store undiluted anti freeze at a temperatu o f below -15°C (5 °F). er and antifreeze Mixing rate of wat Min. atmospheric temperature °C Above -10 °F Above 14 -15 -20 -25 -3 5 -4 -13 -2 Amount of antifre Liters 17.4 eze US gal 4.60 20.9 23.8 26.7 29 5.52 6.29 7.05 7.6 Amount of water Liters 40.6 US gal 10.72 37.1 34.2 31.3 29 9.80 9.03 8.27 7.6 Ratio % 30 36 41 46 5 Antifreeze coolant i s flammable, so keep it away from flame. Antifreeze coolant i s toxic. When removing the drain plug, be careful not t o get water containing antif reeze coolant on you. I gets in your eyes, fl ush your eyes with large amount o f fresh water and se e a doctor at once.

Use antifreeze an d appropriate water for diluting (for details, see "COOLANT AND WATER FOR DILUTION (PA 4-6)") se of an antifreeze density gauge to control the mixing proportions. er whose capacity is larger than the specified coolant volume to catch drained coolant. supply antifreeze coolant and water. ne and tighten 2 valves of the corrosion resistor. cap (1) slowly until it hits the stopper and by so g the internal pressure. cap (1) until it hits the next stopper, while Keep turning the radiator cap (1) until it hits the s to catch the coolant under drain valve (2) at the radiator and under drain valve (3) at the side of ock. lve (2) and drain valve (3), and drain the water.

the antifreeze solution, close drain valve (2), (3), lean water. After the radiator is filled with water, the engine at low idling speed. After the water ises above 90°C (194°F), run the engine for utes. ne and open drain valve (2), (3) to drain the water. the water, clean the cooling system with cleaning agent. ng method, see the instructions for the cleaning agent. We recommend u se of an antifreeze density ga uge to control the mixin Prepare a contain er whose capacity is larger tha n the specified coolant volume to catch dr Prepare a hose to supply antifreeze coolant and 1. Stop the engi 2. Turn radiator doing, relievin 3. Turn radiator depressing it. last stopper. 4.

Put container bottom of the the cylinder bl Open drain va 5. After draining then fill with c start and run temperature r about 10 min 6. Stop the engi 7. After draining For the cleani 1. Stop the engi ne and tighten 2 valves of the corrosion resistor. 2. Turn radiator cap (1) slowly until it hits the s g the internal pressure. cap (1) until it hits the ne 3. Turn radiator Keep turning the radiator cap 6. Stop the engi ne and open drain valve (2), (3 ) to drain the wate 7. After draining the water, clean the cooling sy stem with cleanin ng method, see the instruction s for the cleaning agen 4. Put container s to catch the coolant under dra lve (2) and drain valve (3), an 5.

After draining the antifreeze solution, close d lean water. After the radiator i