WTEC III ELECTRONIC CONTROLS TROUBLESHOOTING MANUAL CODE 64 XX — RETARDER MODULATION REQUEST DEVICE FAULT (Figure 6–23) Copyright © 2001 General Motors Corp. 6–97 Main code 64 indicates the ECU has detected a voltage signal from the retarder modulation request sensor (consisting of a module and a retarder control device) in either the high or low error zone. These codes can be caused by faulty wiring, faulty connections to the resistance module or retarder control device, a faulty resistance module, a faulty retarder control device, or a faulty ECU. Power wire 124 and ground wire 135 for the retarder modulation request sensor are a common power and ground with the TPS and OLS devices.
A short-to-ground on the common power wire causes a “sensor failed low” code for the other devices (codes 21 12, and 14 12). An open or a short-to-ground on retarder modulation request sensor signal wire 164 results in a code 64 12 only. A TPS failure changes the status of the output retarder. The retarder is enabled by the Service Brake Status (wire 137) when a TPS code is active (21 XX). If a code 63 40 is also active, the Service Brake Status (wire 137) is ignored and the retarder will not work. Retarder response problems may not cause retarder modulation request sensor diagnostic codes.
If response questions occur, test the retarder control devices for proper voltage signals at each of the percentage of retarder application settings. Table 6–8 contains the voltage measurements for each device’s application percentage and resistances measured across terminals A and C of the retarder request sensor. Use test wiring harness J 41339 when conducting voltage tests. Main Code Subcode Meaning 64 12 Retarder Modulation Request sensor failed Low (14 counts and below) 64 23 Retarder Modulation Request sensor failed High (232 counts and above) A. Active Indicator Clearing Procedure: • Power down NOTE: Before troubleshooting, read Paragraph 6–6.
Also, check battery and ECU input voltages. NOTE: Intermittent connections or lack of battery-direct power and ground connections can cause this and other electronic control codes. B. Troubleshooting: NOTE: Code 64 12 can be caused when the +5V power line (wire 124) is shorted to ground or open. Wire 124 also provides power for the OLS, TPS, sump temperature sensor, retarder temperature sensor, and shift selectors and is present in all three ECU connectors. 1. Plug in the DDR and set to read retarder counts and percent (0 percent will be between 15 and 60 counts and 100 percent will be between 150 and 233 counts).
A retarder request sensor failed high code can be caused by a short-to-battery of either signal wire 164 or power wire 124 or an open on ground wire 135. An open in the portion of the ground circuit common to the TPS and OLS devices will also result in a code 21 23 and a high fluid level reading. A retarder request sensor failed low code can be caused by an open or short-to-ground on either signal wire 164 or power wire 124. 2. Isolate and repair any wiring problems found. See Appendix E for connector service information. 3. If no wiring or connector problems are found, check the retarder request sensor voltages for each position on each of the retarder request sensors used on the vehicle.
If two resistance modules are used, disconnect one of them when measuring voltage signals from the other. If problems are found, replace the resistance modules or retarder control devices. CAUTION: Using an unmatched ECU/CIN combination may result in additional codes being set or in transmission clutch damage. Using an ECU from another vehicle is not a recommended procedure where the test will involve driving the vehicle. This is because the stored adaptive information is tuned to the original vehicle's transmission and those adaptive settings may not perform as expected in another vehicle. Transmission performance could be worse and damage to the clutches may occur. NOTE:
If using an ECU from another vehicle is unavoidable, the ECU must be set to unadapted shifts and the vehicle must be driven carefully to adapt the shifts to the test vehicle. Refer to Service Information Main Code Subcode Meaning 64 12 Retarder Modulation Request sensor failed Low (14 counts and below) 64 23 Retarder Modulation Request sensor failed High (232 counts and above)