WTEC III ELECTRONIC CONTROLS TROUBLESHOOTING MANUAL S ECTION 7 — INPUT AND OUTPUT FUNCTIONS Copyright © 2001 General Motors Corp. 7–1. INPUT FUNCTIONS Input functions are signals sent into the ECU that prompt the ECU to take action. Input functions are activated and deactivated by switched ignition power or ground (wire 161B) to the ECU (wired through the VIW), or through the MODE button on the shift selector. The following input functions can be activated using the MODE button:
• Secondary Shift Schedule • D1 Selection (Available With Pushbutton Selector Only) • PTO Enable • Auto 2–1 Preselect for 7-Speeds The wiring schematic in Appendix J illustrates installation requirements for input functions and designates specific wire numbers in the transmission control system to be used for the activation of these input functions. The wiring schematic in Appendix J should be used for reference only. Ask the vehicle manufacturer which input functions are programmed, which wires are used, and whether voltage input was positive or ground. Wiring schematics for input and output functions are shown in Appendix P.
The ATDTTM or Pro-Link® 9000 can also be utilized to determine which wire was programmed for a particular input function and the wiring schematic can be consulted to find out if input to the ECU is + or – voltage. Refer to the ATDT User Guide (GN3433EN) or the Pro-Link® 9000 diagnostic tool operator’s manual for further information regarding special input functions and other inhibits. NOTE: The schematic in Appendix J shows the intended use of the control features specified. These features have only been validated in the configuration shown. ANY USE OF THESE FEATURES WHICH DIFFERS FROM WHAT IS SHOWN IS NOT THE RESPONSIBILITY OF ALLISON TRANSMISSION.
Never use chassis ground as an INPUT FUNCTION ground. Chassis ground can carry voltage potential of 1 or 2 volts above battery ground. This non-approved input will CAUTION: “confuse” the ECU and cause erroneous input results. Be sure to use wire 161 which is signal ground. Activating an input function can inhibit transmission operation in the same manner as diagnostic code. Use the ATDTTM or Pro-Link® 9000 to verify an active input function or a diagnostic code inhibit. Refer to the ATDT User Guide (GN3433EN) or the Pro-Link® 9000 Diagnostic Tool Operator’s Manual for further information regarding special input functions and other inhibits.
Also, for more detailed information on input functions, refer to the Sales Tech Data Book “WTEC III Controls and General Information.” The maximum number of input and output functions which may be used in any installation depends upon the transmission model and its features. Refer to Table 7–1. Table 7–1.
Input/Output Function Availability Auxiliary Transmission Number Of Input Number Of Output Transmission Model Controls Functions Functions Functions 6-Speed Models and Retarder 10 + Mode Button 6 HD 4070 MD 3070 Models Transfer Case 11 + Mode Button 6 • Auto 2–1 Preselect for 7-Speeds The wiring schematic in Appendix J illustrates installation requirements for input functions and designates specific wire numbers in the transmission control system to be used for the activation of these input functions. The wiring schematic in Appendix J should be used for reference only.
Ask the vehicle manufacturer which input functions are programmed, which wires are used, and whether voltage input was positive or ground. Wiring schematics for input and output functions are shown in Appendix P. The ATDTTM or Pro-Link® 9000 can also be utilized to determine which wire was programmed for a particular input function and the wiring schematic can be consulted to find out if input to the ECU is + or – voltage. Refer to the ATDT User Guide (GN3433EN) or the Pro-Link® 9000 diagnostic tool operator’s manual for further information regarding special input functions and other inhibits. NOTE: The schematic in Appendix J shows the intended use of the control features specified.
These features have only been validated in the configuration shown. ANY USE OF THESE FEATURES WHICH DIFFERS FROM WHAT IS SHOWN IS NOT THE RESPONSIBILITY OF ALLISON TRANSMISSION. CAUTION: Never use chassis ground as an INPUT FUNCTION ground. Chassis ground can carry voltage potential of 1 or 2 volts above battery ground. This non-approved input will “confuse” the ECU and cause erroneous input results. Be sure to use wire 161 which is signal ground. Activating an input function can inhibit transmission operation in the same manner as diagnostic code. Use the ATDTTM or Pro-Link® 9000 to verify an active input function or a diagnostic code inhibit.
Refer to the ATDT User Guide (GN3433EN) or the Pro-Link® 9000 Diagnostic Tool Operator’s Manual for further information regarding special input functions and other inhibits. Also, for more detailed information on input functions, refer to the Sales Tech Data Book “WTEC III Controls and General Information.” The maximum number of input and output functions which may be used in any installation depends upon the transmission model and its features. Refer to Table 7–1. Table 7–1.
Input/Output Function Availability Transmission Model Auxiliary Transmission Controls Functions Number Of Input Functions Number Of Output Functions 6-Speed Models and HD 4070 Retarder 10 + Mode Button 6 MD 3070 Models Transfer Case 11 + Mode Button 6