40 SEBU7645-06 Product Information Section General Information Table 21 930G Bucket Part Number 251-5412 241-0916 Ground Engaging RATED BUCKET Rated Volume Tools LOAD (HIGH LIFT) Rated Operating | Dump Clearance (A) (B) 3300 mm (130 inches) 1210 mm (47.6 inches) Bolt-on Cutting Edge 2.8 m? (3.7 yd’) 3219 kg (7097 Ib) Teeth 2.7 m? (3.5 yd’) 3198 kg (7050 Ib) 1171 (46.1 mm inches) 3146 kg (6936 Ib) 3300 mm (130 inches) 1210 mm (47.6 inches) Bolt-on Cuiting Edge 3.1 m? (4.1 yd?) 3180 kg (7011 Ib) 3256 mm (128 inches) 1252 mm (49.3 inches) Teeth 2.9 m? (3.8 yd*) 3162 kg (6971 Ib) 3322 mm (131 inches) 1213 mm (47.8 inches) 3.1 m? (4.1 yd?) 3109 kg (6854 Ib) and Bolt-on Cutting Edge 2.8 m?
(3.5 yd?) 3400 kg (7496 Ib) Teeth 2.7 m? (3.5 yd?) 3370 kg (7430 Ib) Teeth and Segments 2.8 m? (3.7 yd’) 3317 kg (7313 Ib) Bolt-on Cutting 5.0 m?° (6.5 yd’) 3051 kg (6726 Ib) Edge 141-6272 mm 2.8 m? (3.7 yd*) Segments 160-8370 3366 (133 inches) Teeth and Segments Teeth 252-6903 Reach Load Bolt-on Cutting 3256 mm 5.0 m? (6.5 yd?) 3361 kg (7410 Ib) mm (49.3 inches) 3391 mm (134 inches) 1103 mm (43.4 inches) 3457 mm 1064 mm (136 inches) (41.9 inches) 3391 mm (134 inches) 1103 mm (43.4 inches) 3171 mm (125 inches) Edge 1252 (128 inches) 3377 1188 mm (129 inches) mm (46.8 inches) 1071 mm (42.2 inches) (1) Rated loads are based upon a standard machine with the following conditions:
Implements, Full fuel tank, ROPS Cab, 80 kg (176 Ib ) operator, 600/65 R25 L3 or equivalent tires, Optional Counterweight, Limited Slip, HD Rear Axle, Guards, and Blue Angel Rated Load for Pallet Forks * 80% of the full turn static tipping load e The minimum lifting capacity the rated load of a particular work tool before per- The rated operating load for rough terrain is defined by the least amount of weight of the following conditions. forming any operation. Make adjustments to the rated load as necessary for non-standard config- ¢ 60% of the full turn static tipping load Failure to comply to the rated load can cause pos- sible personal injury or property damage. Review urations. Note:
Rated loads should be used as a guide. The operator must be aware of the following conditions: e Work tools « Uneven ground * Soft ground e Other poor ground conditions For European applications, the rated load is defined by “EN 474-3”. The rated operating load for a firm, level surface is defined by the least amount of weight of the following conditions. ¢ The minimum lifting capacity For North American applications, the rated operating load is defined by “SAE J1197 Feb 91” as 50% of the full turn static tipping load. The maximum height from the ground to the top face of the forks is given for forks that are horizontal at maximum lift height.
The reach from the front tires to the front face of the forks is given for the forks that are horizontal at maximum lift height.