Crankshaft, Main Bearings and Flywheel/Failure Analysis CRANKSHAFT, MAIN BEARINGS, AND FLYWHEEL SPECIFICATIONS—CONTINUED TORQUES Flywheel Housing-to-Cylinder Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 407 N·m (300 lb-ft) Damper Pulley-to-Crankshaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230 N·m (170 lb-ft) Main Bearing Caps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203 N·m (150 lb-ft) Rear Crankshaft Oil Seal Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 N·m (20 lb-ft) Flywheel-to-Crankshaft . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 N·m (85 lb-ft) Piston Cooling Orifices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 N·m (8 lb-ft) Damper Assembly-to-Pulley . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 N·m (30 lb-ft) Injection Pump Gear Cover-to-Timing Gear Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 N·m (20 lb-ft) Timing Gear Cover-to-Cylinder Block* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 N·m (20 lb-ft) Hub Drive-to-Flywheel . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 N·m (85 lb-ft) Magnetic Pickup-to-Timing Gear Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 N·m (10 lb-ft) * See INSTALL TIMING GEAR COVER—NON-AUXILIARY DRIVE ENGINES, later in this group, for proper cap screw tightening sequence. RG,CTM42,G15,47-19-24MAR95 CRANKSHAFT AND MAIN BEARING FAILURE ANALYSIS Scored Main Bearing: (Diagnosis also applies to connecting rod bearing.) Inconsistent Wear Pattern: Oil starvation. Contaminated oil. Engine parts failure. Excessive heat. Poor periodic service. Misaligned or bent connecting rod. Warped or bowed crankshaft. Distorted cylinder block.
15 8 Broken Main Bearing Caps: Improper installation. Dirt between bearing and crankshaft journal. Low oil pressure. Oil pump failure. Galled or “Wiped” Bearings: Fuel in lubricating oil (incomplete combustion). Coolant in lubrication system (cracked block, liner seal failure, or leaking water pump seal with plugged hole). Insufficient bearing oil clearance. Parts not lubricated prior to engine operation. Wrong bearing size. Cracked, Chipped or Broken Bearings: Overspeeding. Excessive idling. Lugging. Excessive oil clearance. Improper installation. CTM42 (24MAR95) 15-8 6076 Diesel Engines—S.N. (500000— ) S11,2015,C -19-29SEP94 160101 PN=137