Piston Ring Connecting Rod Item Service Standard Service Limit Piston and Piston Pin Clearance mm (in) 0.004 — 0.017 (0.0002 — 0.0007) Clearance should be wide enough for the piston pin to be inserted under the condition where the piston is heated to the tempera- ture of 80°C to 100°C (176°F to 212°F). 0.04 (0.0016) When an abnormal striking sound is heard, replace the piston and the pis- ton pin.
Item Service Standard Service Limit Piston Ring Gap (Inside the cylinder) mm (in) 4HF1 4HF1-2 1st Compression Ring 0.24 — 0.39 (0.0094 — 0.0153) 1.50 (0.0591) 2nd Compression Ring 0.35 — 0.50 (0.0138 — 0.0197) 1.50 (0.0591) Oil Ring 0.02 — 0.40 (0.0008 — 0.0157) 1.50 (0.0591) 4HG1 4HG1-T 1st Compression Ring 0.24 — 0.39 (0.0094 — 0.0153) 1.50 (0.0591) 2nd Compression Ring 0.35 — 0.50 (0.0138 — 0.0197) 1.50 (0.0591) Oil Ring 0.15 — 0.35 (0.00591 — 0.0138) 1.50 (0.0591) 4HE1-TC 1st Compression Ring 0.24 — 0.40 (0.0094 — 0.0157) 1.50 (0.0591) 2nd Compression Ring 0.30 — 0.40 (0.0118 — 0.0157) 1.50 (0.0591) 3rd Compression Ring 0.30 — 0.40 (0.0118 — 0.0157) 1.50 (0.0591) Oil Ring 0.02 — 0.40 (0.0008 — 0.0157) 1.50 (0.0591) Piston Ring & Piston Ring Groove Clearance mm (in) 4HF1 4HF1-2 1st Compression Ring 0.062 — 0.092 (0.0024 — 0.0036) 0.2 (0.0078) 2nd Compression Ring 0.04 — 0.08 (0.0015 — 0.0031) 0.15 (0.0059) Oil Ring 0.02 — 0.06 (0.0008 — 0.0024) 0.15 (0.0059) 4HG1 4HG1-T 1st Compression Ring 0.062 — 0.092 (0.0024 — 0.0036) 0.2 (0.0078) 2nd Compression Ring 0.04 — 0.08 (0.0015 — 0.0031) 0.15 (0.0059) Oil Ring 0.02 — 0.06 (0.0008 — 0.0024) 0.15 (0.0059) 4HE1-TC 1st Compression Ring 0.09 — 0.13 (0.0035 — 0.0051) 0.2 (0.0078) 2nd Compression Ring 0.09 — 0.13 (0.0035 — 0.0051) 0.2 (0.0078) 3rd Compression Ring 0.09 — 0.13 (0.0035 — 0.0051) 0.2 (0.0078) Oil Ring 0.03 — 0.07 (0.0012 — 0.0028) 0.15 (0.0059) The direction of the piston ring connecting end Alternately at 180°.
Don’t position the connecting end in the side pressure direction. Place the connecting end of the oil ring and that of the expander coil at 180° alternately. Item Service Standard Service Limit Connecting Rod Align- mm (in) ment Distortion 0.05 (0.002) or less 0.20 (0.008) Parallelism 0.05 (0.002) or less 0.20 (0.008) Connecting Rod Small End Bush- mm (in) ing and Piston Pin Clearance 0.012 — 0.027 (0.0005 — 0.0011) There must be clearance enough to rotate the piston pin while holding it lightly with its large end fixed. 0.05 (0.002) Connecting Rod Bearing Spread mm (in) 70 (2.77) or more