Isuzu — Isuzu N Series Training Manual

er there is no abnormality in operation of the brake system. 13. After the air bleeding procedure for individual wheel is completed, inspect the fluid level of the reservoir tank. If it is insufficient, replenish brake fluid. Do not overfill above “MAX” level. 14. Stop the engine. 14. Check the state of the hydraulic oil in the reservoir, and if there is no foaming or change in the level of the oil, the operation of bleeding the air out is con- sidered completed. If any foam remains, let it stand for a while, wait for the foam to dissipate, then re- peat the above steps 12 — 13. Notice:

Precautions when bleeding the air from the brake fluid pressure system When doing air bleeding of the brake fluid pressure sys- tem, such as the master cylinder or wheel cylinder, ver- ify that the air has been bled out of the hydro boost, and make sure that the engine is on. Be aware that if air bleeding of the brake fluid system is to be done with the engine off, air bleeding cannot be done. If air bleeding of the brake fluid pressure system is to be done at the same time as air bleeding of the hydro boost, do so when the operation of the above hydro boost air bleeding method 10 has been completed. Supply Parts Replacement 1.

The hydro boost is a precision part that operates with high-pressure hydraulic oil. Never remove any parts from the hydro boost except replacement parts. Trouble may occur if a part other than a replace- ment part is removed and a non-matching part is included or the assembly is bad. For example, mi- soperation may occur and the brake becomes inef- fective, or a bad seal may allow high-temperature hydraulic oil under high pressure to spatter and cause a burn. 2. The hydraulic oil to be used for the hydro boost is ATF DEXRON ® III. Using any other hydraulic oil could adversely affect the rubber parts and cause poor operation or oil leakage.

In particular, the hydraulic oil for the hydro boost is quite different from the brake fluid that is used in the master cylinder. Be careful that hydro boost parts do not come into contact with the brake fluid for the master cylinder, and that master cylinder parts do not come into contact with the hydraulic oil for the hydro boost. Any mixing together of the hydraulic oil for the hy- dro boost and the brake fluid for the master cylin- der could cause degradation such as the swelling of rubber parts, brake failure due to oil leakage or bad operation, or a serious mishap such as a vehi- cle fire caused by brake friction. 3.

Operation of the pump while the engine is on will cause the hydro boost hydraulic oil to get hot. In particular, frequent repeated operation of the brake will sometimes increase the temperature of the hy- draulic oil in the hydro boost assembly to 100 ° C (212 ° F) or more. Be careful in handling. When performing work such as removing the hydro boost assembly from the vehicle, before starting Hydraulic Booster Line Bleeding Bleeding Precautions After removing the hydro boost assembly or piping and making repairs, do not run the vehicle until you perform the below-described air bleeding and then verify that ev- erything is normal, including hydro boost boosting and accumulator operation.

Bleeding Procedure 1. Attach the hydro boost and the master cylinder to the vehicle and connect the piping. 2. Fill the hydro boost reservoir with hydraulic oil be- tween its minimum and maximum range. 3. Turn the engine on for about 5 seconds. 4. Then turn the engine off and check the quantity of hydraulic oil in the reservoir. 5. If the hydraulic oil is below the minimum, pour in more hydraulic oil so that it is in the range from min- imum to maximum. 6. Repeat the above steps 2 — 5 until there is no foaming or change in the level of the hydraulic oil in the reservoir.

But if the hydraulic oil foams during the above steps, let it stand for a while, wait for the foam to dissipate, then continue the work. 7. With the engine on, repeatedly press the brake pedal slowly about five times. 8. Then turn the engine off and check the quantity of hydraulic oil in the reservoir. If the hydraulic oil is below the minimum, once again pour in more hy- draulic oil so that it is in the range from minimum to maximum. 9. Leaving the engine off, repeatedly press the brake pedal at least ten times. 10. Verify that there is no foam or change in the level of the hydraulic oil in the reservoir.

If any foam re- mains, let it stand for a while, wait for the foam to dissipate, then repeat the above steps 7 — 9. 11. If it is necessary at this time to bleed out the air from the brake fluid pressure system, such as the master cylinder or the wheel cylinder, be sure to first complete step 10 above and make sure that the engine is on. 12. With the engine on, strongly press the brake pedal as far as the booster full load region slowly and re- peatedly about 30 times (for 1 — 3 seconds each time). When doing so, do not keep the pedal at the full load region (no longer than 1 second). 13. Then turn the engine off and repeatedly press the brake pedal at least 10 times.