daewoo DE12T / P126TI — Daewoo DE12T / P126TI User Manual

Standard bolt tightening torque table Refer to the following table for bolts other than described above. Others: 1. The above torque rating have been determined to 70% or so of the limit value for bolt elasticity. 2. Tension is calculated by multiplying tensile strength by cross section of thread. 3. Special screws should be tightened to 85% or so of the standard value. For example, a screw coated with MoS2 should be tightened to 60% or so of the standard value.

- 131 - Diameter x pitch (mm) Degree of strength 3.6 4.6 4.8 5.6 5.8 6.6 6.8 6.9 8.8 10.9 12.9 (4A) (4D) (4S) (5D) (5S) (6D) (6S) (6G) (8G) (10K) (12K) Limit value for elasticity (kg/mm2) 20 24 32 30 40 36 48 54 64 90 108 Tightening torque (kg•m) M5 0.15 0.16 0.25 0.22 0.31 0.28 0.43 0.48 0.50 0.75 0.90 M6 0.28 0.30 0.45 0.40 0.55 0.47 0.77 0.85 0.90 1.25 0.5 M7 0.43 0.46 0.70 0.63 0.83 0.78 1.20 1.30 1.40 1.95 2.35 M8 0.70 0.75 1.10 1.00 1.40 1.25 1.90 2.10 2.20 3.10 3.80 M8x1 0.73 0.80 1.20 1.10 1.50 1.34 2.10 2.30 2.40 3.35 4.10 M10 1.35 1.40 2.20 1.90 2.70 2.35 3.70 4.20 4.40 6.20 7.40 M10x1 1.50 1.60 2.50 2.10 3.10 2.80 4.30 4.90 5.00 7.00 8.40 M12 2.40 2.50 3.70 3.30 4.70 4.20 6.30 7.20 7.50 10.50 12.50 M12x1.5 2.55 2.70 4.00 3.50 5.00 4.60 6.80 7.70 8.00 11.20 13.40 M14 3.70 3.90 6.00 5.20 7.50 7.00 10.00 11.50 12.00 17.00 20.00 M14x1.5 4.10 4.30 6.60 5.70 8.30 7.50 11.10 12.50 13.00 18.50 22.00 M16 5.60 6.00 9.00 8.00 11.50 10.50 17.90 18.50 18.00 26.00 31.00 M6x1.5 6.20 6.50 9.70 8.60 12.50 11.30 17.00 19.50 20.00 28.00 33.00 M18 7.80 8.30 12.50 11.00 16.00 14.50 21.00 24.20 25.00 36.00 43.00 M18x1.5 9.10 9.50 14.50 12.50 18.50 16.70 24.50 27.50 28.00 41.00 49.00 M20 11.50 12.00 18.00 16.00 22.00 19.00 31.50 35.00 36.00 51.00 60.00 M20x1.5 12.80 13.50 20.50 18.00 25.00 22.50 35.00 39.50 41.00 58.00 68.00 M22 15.50 16.00 24.50 21.00 30.00 26.00 42.00 46.00 49.00 67.00 75.00 M22x1.5 17.00 18.50 28.00 24.00 34.00 29.00 47.00 52.00 56.00 75.00 85.00 M24 20.50 21.50 33.00 27.00 40.00 34.00 55.00 58.00 63.00 82.00 92.00 M24x1.5 23.00 25.00 37.00 31.00 45.00 38.00 61.00 67.00 74.00 93.00 103.00