CROP PROCESSING - THRESHING Axial flow threshing Power from the engine is directed through the PTO gearbox to drive the engine clutch, ring, planetary carrier, rotor gearbox and rotor. The hydro pump and motor will control the speed of the sun gear to change the speed at which the planetary carrier is walking around it. This is the typical operating mode in the field, where the engine drive is used to power the rotor drive, and the hydrostat drive is used to control the rotor speed. ELECTRICAL COMPONENTS Universal Display Plus monitor - The Universal Display Plus monitor, located adjacent to the right hand console, is used to for two way communication between the combine and the operator.
Separator Switch, S-30 - the separator switch, located in the right hand console, is a three-position switch to provide: 1. Forward detented position; is used to provide a signal to the CCM3 to request for separator engagement. It also provides the power that will be used by the CCM3 to power the rotor drive solenoids. This provides for a positive disengagement. 2. Center detented position; is used to disengaged the separator and return it to an idle state. 3. Rearward momentary position; is used to direct a signal to the RHM to activate the rotor De-Slug mode of operation.
Rotor Speed Increase/Decrease Control, S-17 - The rotor speed switch, located on the right hand console, provides the operator with a method of changing and controlling the desired rotor speed. If the switch is momentarily pressed the rotor speed will be changed at the rate of 10 RPM per toggle, if continually pressed the rotor will change 10 RPM/second. The switch is also used to provide rotor rotating directional control during de-slug operation; rotor increase causes forward (normal clockwise) rotor rotation and rotor decrease causes reverse (counter clockwise) rotor rotation.
CCM1 Controller - The CCM1 controller, located under the instructor’s seat, controls the concave operation by receiving CAN bus signals from the RHM, display and sensors, and motor. CCM3 Controller - The CCM3 controller, located under the instructor’s seat, controls the rotor operation by receiving CAN bus signals from the RHM, display and sensors, and controlling solenoids. Feeder Switch, S-31 - The feeder switch is supplied power once the separator switch is placed into the RUN (forward) position.
Rotor Pump Solenoid, L-48 & L-49 - The pump solenoid is a double solenoid used to control the position of the pump swash plate in order to provide variable pump displacement and rotation direction. The pump swash plate is defaulted to the Neutral position when both solenoids are deactivated. The CCM3 controls both solenoids. Located: Hydro pump mounted on the PTO gearbox. Rotor Drive Motor RPM Sensor, B-58 - The rotor drive motor RPM sensor, located on the rotor motor housing, mounted on the PTO gear box, is used by the CCM3 to calculate input RPM to the POWER PLUS drive by the hydrostatic motor. This RPM is used for five functions:
The rotor drive motor RPM sensor is a Hall-effect sensor and requires no adjustments. It is threaded in until the O-ring is tight; torque not to exceed 15 Nm ( 11 lb ft ). 1. During rotor acceleration, it is used in conjunction with rotor speed sensor to calculate which gear range the rotor gearbox is currently in. 2. It is used to signal a motor over-speed condition during a rotor slug event. 3. It is used to assure speed match between planetary ring and engine RPM for rotor re-engagement. 4. It is used with the rotor and engine speed information to help control rotor deceleration, minimizing the time it takes to bring the rotor speed to zero after disengagement. 5.
It is used with engine speed information to help the CCM-3 calculate the rotor speed in the event that the rotor speed sensor fails during operation. 9714 1 27/05/2004 K.40.C / 12 1. Engine 6. Rotor Drive Motor 2. Control Module CCM-3 7. Planetary Gear Assembly. (R-Ring, P-Planetary, S - Sun Gear) 3. PTO Gearbox 8. Ring-to-Frame Brake 4. Rotor Drive Pump 9. Rotor Gearbox 5. Engine-to-Ring Clutch 10. Rotor