Case IH AFX8010 — THRESHING Axial flow threshing

CROP PROCESSING - THRESHING Axial flow threshing B. If there is continuity to ground, continue with step 5 . 6. Disconnect connector X004 . Use a multimeter to check for continuity between connector X004 pin 30 and chassis ground. There should not be continuity to ground. A. If there is continuity to ground, there is a short to ground in the cab main (CM) harness between connector X004 and relay base K16 terminal 4 wire 695 white. Locate the short and repair. B. If no continuity is found, there is a short to ground in the main frame (MF) harness between connector X004 and connector X190 wire 695 white. Locate the short and repair. 7. Concave and covers operate in one direction only.

Fault codes indicate a short to ground. Disconnect both the concave motor connector X190 and covers motor connector X289 . Use a multimeter to measure the resistance of the concave motor connector X190 between pin 1 and pin 2, and the covers motor connector X289 between pin A and pin B. The proper resistance range for both motors is 1.0 - 5.0 ohms . A. If the concave motor is out of specification, replace concave motor. B. If the grain tank covers motor is out of specification, replace covers motor. C. If both motors are within specification, continue with Step 7 . 8. Check for continuity between concave motor connector X190 pin 1 and chassis ground.

Flex the main frame (MF) harness while making this check. Next check for continuity between connector X289 pin B and chassis ground. Flex the grain tank jumper and main frame (MF) harnesses while making this check. There should not be continuity to ground. A. If no continuity to ground is found, erase fault code and continue operation. B. If there is continuity to ground, continue with Step 8 . 9. Disconnect connector X456 . Use a multimeter to check for continuity between the main frame (MF) harness end of connector X456 pin 1 and chassis ground. There should not be any continuity. A.

If there is no continuity to ground, there is a short to ground in the concave extension (CC) harness between connector X456 and connector X190 wire 694 gray. Locate the short and repair. B. If there is continuity to ground, continue with Step 8 . 10. Disconnect connector X195 . Use a multimeter to check for continuity between connector X195 pin 3 and chassis ground. A. If continuity is found, there is a short to ground in the main frame (MF) harness between connector X456 , connector X195 and connector X019 pin J2-1 wires 694 gray, 693 gray and 522 gray. Locate the short and repair. B.

If no continuity is found, there is a short to ground in the grain tank jumper harness between connector X195 and connector X289 wire 693 gray. Locate the short and repair. 11. Concave does not operate in either direction. Fault code indicates an open circuit. Disconnect the concave motor connector X190 . Measure the resistance on connector X190 between pin 1 and pin 2. The proper resistance range for the motor is 1.0 - 5.0 ohms . A. If out of specification, replace concave motor. 12. Replace the concave/covers relay K-16 with a known good relay. Reattach connector X176 and operate the concaves. B. If the motor coil resistance is within specification, continue with Step 10 . A.

If the concaves are now working, the concave/covers relay K-16 has failed. Replace the relay. B. If the concaves still do not work, continue with Step 11 . 13. Disconnect concave motor connector X190 . Turn key switch ON. Operate the concave motor using the Universal Display Plus "DIAG" screen controls. Use a multimeter to measure the voltage between connector X190 pin 2 and chassis ground. 9714 1 27/05/2004 K.40.C / 90