DISTRIBUTION SYSTEMS - LIGHTING SYSTEM Marker light - Overview (A.40.A.12 - C.10.A.10) AFX8010 DESCRIPTION Current travels across the electrical system buss bar to reach fuse F-49. Wiring harness - Electrical schematic frame 27 (A.30.A.88 - C.20.E.27) Wiring harness - Electrical schematic frame 36 (A.30.A.88 - C.20.E.36) Current passes through fuse F-49 and a wire splice to reach connector X256 pin 5 of the Road Light Switch (S-26) (control stalk found on the left side of the steering column). Rotating the Road Light Switch (S-26) to the second (marker lights) or third position (road lights) causes current to cross from pin 5 to reach pin 1.
Current exits pin 1 of the road light switch (and travels to pin 5 of the Light Control Relay (K-02). Current travels from pin 5 to pin 1 of the light control relay (K-02). A jumper wire at pin 1 of the light control relay delivers current to connector X018 Pin J1-21 of CCM-1. CCM-1 then activates the backlighting circuit. Refer to the backlighting circuit for more information. Back light - Overview (A.40.A.24 - C.10.A.10) Wiring harness - Electrical schematic frame 34 (A.30.A.88 - C.20.E.34) Current enters pin 1 of the light control relay and reaches the coil within the relay. The ground path to the relay exits pin 2 and travels to the cab floor ground location #3.
This causes the light control relay to energize and send current from pin 3 to fuse F-20. A jumper wire sends current from fuse F-20 to fuse F-21. FUSE F-20 (7.5 Amp) Current exits fuse F-20 and travels through connector X005 to reach a wire splice. The wire splice sends current to three different paths: The first path (French Models Only) sends current through connectors X009 , X105 and X323 to reach pin A of the Unload Tube Marker LT (E-39). The ground path exits pin B and travels through connector X105 and X009 to reach the front frame ground location #2. This causes the Unload Tube Marker Light to illuminate.
Wiring harness - Electrical schematic frame 35 (A.30.A.88 - C.20.E.35) The second path sends current through connector X024 to reach a wire splice. The wire splice splits the current into two different paths. The first path sends current through connector X285 to reach pin 58L of the Trailer Outlet (J-09). This provides current for the LH Trailer Marker Lights (if equipped). The second path sends current through connector X071 to reach a wire splice. The wire splice splits the current into two different paths. The first path (European Models Only) sends current to the LH Rear Flashing Lamp (EU) (E-05).
The ground path exits pin 4 and travels through a wire splice and connector X071 to reach the rear frame ground location #1. This causes the LH Rear Marker Lamp (EU) to illuminate. The second path (North American Models Only) sends current to the LH Brake / Tail Lamp (NA) (E-11). The ground path exits pin C and travels through a wire splice and connector X071 to reach the rear frame ground location #1. This causes the LH Brake / Tail Lamp (NA) to illuminate. Wiring harness - Electrical schematic frame 34 (A.30.A.88 - C.20.E.34) The third path sends current through connector X160 to reach a wire splice.
The wire splice sends current to the LH Front Hazard Lamp (E-03), LH Position Lamp E-50 (European Models Only), and the LH Front Austria Lamp (E-54). The ground paths to the lights listed above travel through a wire splice and connector X160 to reach the front frame ground location #2. This causes the lights to illuminate. FUSE F-21 (7.5 Amp) Current flows from fuse F-21 and splits into two paths: Wiring harness - Electrical schematic frame 33 (A.30.A.88 - C.20.E.33) The first path (European Only) sends current through connectors X031 , and X007 , to reach header connector X032 . If equipped with a header, current passes through connector X032 and reaches a wire splice.
The wire splice sends current to the Header LH Marker LT (EU) (E-41) and the Header RH Marker LT (EU) (E-40). The ground path for the marker lights travels through a wire splice, connectors X032 and X007 to reach the front frame ground location #2. This causes the Header LH Marker LT (EU) and the Header RH Marker LT (EU) (E-40) to illuminate. Wiring harness - Electrical schematic frame 34 (A.30.A.88 - C.20.E.34) The second path sends current from fuse F-21 through connector X005 to reach a wire splice. The wire splice splits the current into three paths: 9668 1 27/05/2004 A.40.A / 11