Case IH AFX8010 — LIGHTING SYSTEM

DISTRIBUTION SYSTEMS - LIGHTING SYSTEM Road Light Switch Power Current travels from the electrical system buss bar to reach fuse F-38 (7.5-amp) Wiring harness - Electrical schematic frame 29 (A.30.A.88 - C.20.E.29) . Current passes through fuse F-38 and connector X068 to reach the key switch (S-02). When the key switch is turned to the "ACC/Run" position, current flows from connector X068 pin 6 to reach a wire splice. The wire splice directs the current to connector X256 pin 6 of the road light switch (S-26) Wiring harness - Electrical schematic frame 36 (A.30.A.88 - C.20.E.36) .

Left Turn Operation When the road light switch is moved to the LH Turn position (control stalk pulled toward the operator), current crosses from pin 6 to pin 3 and reaches a wire splice. The wire splice directs the current to two different paths: The first path sends current to connector X018 pin J1-2 of CCM-1. Current enters pin J1-2 to inform CCM-1 that the left-hand turn signal circuit has been activated. If the combine is in "Field" mode and the work lights are "On", CCM-1 will activate the side work lights. The second path sends current through connector X033 to reach connector X255 pin 8 of the flasher module (A-05).

Depending on the configuration of the combine, the flasher module then activates the left turn signal circuit in ISO (European) or NASO (North American) mode. ISO or NASO Mode Selection Whether the combine flashing lights will operate in ISO or NASO mode is controlled by current sent from CCM-2 to the flasher module. When configured for ISO operation, CCM-2 sends current from pin J1-5 through connector X033 to pin 9 of the flasher module (A-05). When in NASO mode, current will not be sent to pin 9 of the flasher module. The flasher module will function accordingly.

Pin 10 of the Flasher Module (Pulsing) Wiring harness - Electrical schematic frame 33 (A.30.A.88 - C.20.E.33) Pulsing current exits pin 10 of the flasher module and passes through connectors X033 , X004 , X024 , and X071 , to reach connector X242 pin A of the LH Flashing Lamp (E-07). The ground path exits pin B and passes through a wire splice and connector X071 to reach the rear frame ground location #1. This causes the LH flashing lamp (NA) (E-07) to flash on and off. Pin 3 of the Flasher Module (Pulsing) Pulsing current exits pin 3 and reaches a wire splice. The wire splice directs current to two paths.

The first path sends pulsing current through connector X257 to reach pin 7 of the Turn Indicator (Left) (E-09) found on the steering column. The ground path exits pin 9 and travels through a wire splice and connector X033 to reach the cab floor ground location #3. This causes the left light within the turn indicator to flash on and off. The second path sends pulsing current through connectors X033 and X005 to reach a wire splice. Wiring harness - Electrical schematic frame 34 (A.30.A.88 - C.20.E.34) The wire splice sends pulsing current to three different paths:

North American Models Wiring harness - Electrical schematic frame 33 (A.30.A.88 - C.20.E.33) - The first path sends pulsing current through connector X008 and connector X007 to reach connector X032 . If a header is equipped, the header harness is used to send pulsing current through connector X303 to the LH Header Flashing Lamp (NA) (E-01). The ground path exits connector X303 and passes through a wire splice, connector X032 , and connector X007 to reach the front frame ground location #2. This causes the LH Header Flashing Lamp (NA) (E-01) to flash on and off. The second path sends pulsing current through connector X160 to a wire splice.

Wiring harness - Electrical schematic frame 34 (A.30.A.88 - C.20.E.34) The wire splice sends pulsing current to the LH Front Hazard Lamp (E-03) (All Markets) and the LH Flashing Lamp (E-52) (European Models Only). The ground path for the lights travels through a wire splice and connector X160 to reach the front frame ground location #2. This causes the LH Front Hazard Lamp (E-03) and the LH Flashing Lamp (E-52) (European Models Only) to flash on and off. The third path sends pulsing current through connector X024 to reach a wire splice.

Wiring harness - Electrical schematic frame 35 (A.30.A.88 - C.20.E.35) The wire splice sends pulsing current through connector X285 to reach pin L on the Trailer Outlet (J-09). NASO MODELS ONLY (North American) With the combine in NASO mode and the left turn signal activated, pulsing current flows from pin 10 and pin 3 and solid current travels from pin 4 of the flasher module (A-05). 9668 1 27/05/2004 A.40.A / 15