Case IH AFX8010 — LIGHTING SYSTEM

DISTRIBUTION SYSTEMS - LIGHTING SYSTEM Pin 4 of the Flasher Module (Solid) Wiring harness - Electrical schematic frame 33 (A.30.A.88 - C.20.E.33) Solid current exits pin 4 and reaches a wire splice. The wire splice directs current to two paths. The first path sends solid current through connector X257 to reach pin 10 of the Turn Indicator (Right) (E-09) found on the steering column. The ground path exits pin 9 and travels through a wire splice and connector X033 to reach the cab floor ground location #3. This causes the right light within the turn indicator to Illuminate. The second path sends solid current through connectors X033 and X005 to reach a wire splice.

Wiring harness - Electrical schematic frame 34 (A.30.A.88 - C.20.E.34) The wire splice sends pulsing current to three different paths: Wiring harness - Electrical schematic frame 33 (A.30.A.88 - C.20.E.33) North American Models - The first path sends solid current through connector X008 and connector X007 to reach connector X032 . If a header is equipped, the header harness is used to send solid current through connector X304 to the RH Header Flashing Lamp (NA) (E-02). The ground path exits connector X304 and passes through a wire splice, connector X032 , and connector X007 to reach the front frame ground location #2. This causes the RH Header Flashing Lamp (NA) (E-02) to illuminate.

Wiring harness - Electrical schematic frame 34 (A.30.A.88 - C.20.E.34) The second path sends solid current through connector X165 to a wire splice. The wire splice sends solid current to the RH Front Hazard Lamp (E-04). The ground path for the lamp travels through a wire splice and connector X165 to reach the front frame ground location #2. This causes the RH Front Hazard Lamp (E-04) to illuminate. Wiring harness - Electrical schematic frame 35 (A.30.A.88 - C.20.E.35) The third path sends solid current through connector X024 to reach a wire splice. The wire splice sends solid current through connector X285 to reach pin R on the Trailer Outlet (J-09).

This causes the trailer light to illuminate (if equipped). RIGHT-HAND FLASHER (TURN SIGNAL) CIRCUIT NOTE: Failed bulbs, poor connections, or broken circuitry may cause flasher to flash on and off at an irregular pace. If trailer lights are connected, the lighting system will function differently. For example, when trailer lights are connected to the lighting circuit, a bulb failure will have less effect on the operation of the circuit. NOTE: If the road/field mode switch is in the "Field" position and the work lights are "ON", activating the right turn signal causes the side work lights to illuminate. This is to help the operator negotiate a turn in low light conditions.

The right hand control module, CCM-1, and CCM-2 communicate through the network to control this feature. See the work light circuit for more information on the side work lights. Flasher Module Power Wiring harness - Electrical schematic frame 33 (A.30.A.88 - C.20.E.33) Current travels from the electrical system buss bar to reach fuse F-56 (15-amp). Current passes through fuse F-56, connector X033 and a wire splice to reach pin 1 of the flasher module (A-05). The ground path exits pin 6 and travels through a wire splice and connector X033 to reach the cab floor ground location #3. This provides power for the flasher module to function.

Road Light Switch Power Wiring harness - Electrical schematic frame 29 (A.30.A.88 - C.20.E.29) Current travels from the electrical system buss bar to reach fuse F-38 (7.5-amp). Current passes through fuse F-38 and connector X068 to reach the key switch (S-02). When the key switch is turned to the "ACC/Run" position, current flows from connector X068 pin 6 to reach a wire splice. The wire splice directs the current to connector X256 pin 6 of the road light switch (S-26) Wiring harness - Electrical schematic frame 36 (A.30.A.88 - C.20.E.36) .

Right Turn Operation When the road light switch (S-26) is moved to the RH Turn position (control stalk pushed away from the operator), current crosses from pin 6 to pin 2 and reaches a wire splice. The wire splice directs the current to two different paths: The first path sends current to connector X018 pin J1-9 of CCM-1. Current enters pin J1-9 to inform CCM-1 that the right-hand turn signal circuit has been activated. If the combine is in "Field" mode and the work lights are ON, CCM-1 will activate the side work lights. The second path sends current through connector X033 to reach connector X255 pin 7 of the flasher module (A-05).

Depending on the configuration of the combine, the flasher module then activates the right turn signal circuit in ISO (European) or NASO (North American) mode. ISO or NASO Mode Selection 9668 1 27/05/2004 A.40.A / 16