DISTRIBUTION SYSTEMS - LIGHTING SYSTEM Whether the combine flashing lights will operate in ISO or NASO mode is controlled by current sent from CCM-2 to the flasher module. When configured for ISO operation, CCM-2 sends current from pin J1-5 through connector X033 to pin 9 of the flasher module (A-05). When in NASO mode, current will not be sent to pin 9 of the flasher module. The flasher module will function accordingly. Pin 11 of the Flasher Module (Pulsing) Pulsing current exits pin 11 of the flasher module (A-05) and passes through connectors X033 , X004 , X024 , and X071 , to reach connector X245 pin A of the RH Flashing Lamp (E-08).
The ground path exits pin B and passes through a wire splice and connector X071 to reach the rear frame ground location #1. This causes the RH flashing lamp (NA) (E-08) to flash on and off. Pin 4 of the Flasher Module (Pulsing) Wiring harness - Electrical schematic frame 33 (A.30.A.88 - C.20.E.33) Pulsing current exits pin 4 and reaches a wire splice. The wire splice directs current to two paths: The first path sends pulsing current through connector X257 to reach pin 10 of the Turn Indicator (Right) (E-09) found on the steering column. The ground path exits pin 9 and travels through a wire splice and connector X033 to reach the cab floor ground location #3.
This causes the right light within the turn indicator to flash on and off. The second path sends pulsing current through connectors X033 and X055 to reach a wire splice. The wire splice sends pulsing current to three different paths: North American Models - The first path sends pulsing current through connector X008 and connector X007 to reach connector X032 . If a header is equipped, the header harness is used to send pulsing current through connector X304 to the RH Header Flashing Lamp (NA) (E-02). The ground path exits connector X304 and passes through a wire splice, connector X032 , and connector X007 to reach the front frame ground location #2.
This causes the RH Header Flashing Lamp (NA) (E-02) to flash on and off. Wiring harness - Electrical schematic frame 34 (A.30.A.88 - C.20.E.34) The second path sends pulsing current through connector X165 to a wire splice. The wire splice sends pulsing current to the RH Front Hazard Lamp (E-04) (All Markets) and the RH Flashing Lamp (E-51) (European Models Only). The ground path for the lights travels through a wire splice and connector X165 to reach the front frame ground location #2. This causes the RH Front Hazard Lamp (E-04) and the RH Flashing Lamp (E-51) (European Models Only) to flash on and off.
Wiring harness - Electrical schematic frame 35 (A.30.A.88 - C.20.E.35) The third path sends pulsing current through connector X024 to reach a wire splice. The wire splice sends pulsing current through connector X285 to reach pin R on the Trailer Outlet (J-09). NASO MODELS ONLY (North American) Wiring harness - Electrical schematic frame 33 (A.30.A.88 - C.20.E.33) With the combine in NASO mode and the right turn signal activated, pulsing current flows from pin 11 and pin 4 and solid current travels from pin 3 of the flasher module (A-05). Pin 3 of the Flasher Module (Solid) Solid current exits pin 3 and reaches a wire splice. The wire splice directs current to two paths.
The first path sends solid current through connector X257 to reach pin 7 of the Turn Indicator (Left) (E-09) found on the steering column. The ground path exits pin 9 and travels through a wire splice and connector X033 to reach the cab floor ground location #3. This causes the Left light within the turn indicator to Illuminate. The second path sends solid current through connectors X033 and X005 to reach a wire splice. The wire splice sends pulsing current to three different paths: The first path (North American models only) sends solid current through connector X008 and connector X007 to reach connector X032 .
If a header is equipped, the header harness is used to send solid current through connector X303 to the LH Header Flashing Lamp (NA) (E-01). The ground path exits connector X303 and passes through a wire splice, connector X032 , and connector X007 to reach the front frame ground location #2. This causes the LH Header Flashing Lamp (NA) (E-01) to illuminate. Wiring harness - Electrical schematic frame 34 (A.30.A.88 - C.20.E.34) The second path sends solid current through connector X165 to a wire splice. The wire splice sends solid current to the RH Front Hazard Lamp (E-04).
The ground path for the lamp travels through a wire splice and connector X165 to reach the front frame ground location #2. This causes the RH Front Hazard Lamp (E-04) to illuminate. Wiring harness - Electrical schematic frame 35 (A.30.A.88 - C.20.E.35) The third path sends solid current through connector X024 to reach a wire splice. The wire splice sends solid current through connector X285 to reach pin R on the Trailer Outlet (J-09). This causes the trailer light to illuminate (if equipped). 9668 1 27/05/2004 A.40.A / 17