DISTRIBUTION SYSTEMS - LIGHTING SYSTEM Brake light - Overview (A.40.A.14 - C.10.A.10) AFX8010 BRAKE LIGHTS CIRCUIT The brake lights warn motorists that the combine is slowing or stopping. The brake lights are activated when the brake pedal is depressed, the hydrostatic control lever is pulled back quickly, or the engine is automatically shutdown. The brake light circuit consists of the following components: 2 Brake Lights (E-11, E-12 NASO), (E-05, E-06 ISO) CCM2 Brake Pressure Switch (S-39) Ground Speed Pot (R-04) Brake Light Relay (K-33) CCM-2 activates the brake lights when any of the following conditions are met:
Brake Pedal Depressed Wiring harness - Electrical schematic frame 09 (A.30.A.88 - C.20.E.09) When the brake pedal is depressed, the pressure created in the brake lines causes the Brake Pressure Switch S-39 to close and complete the ground path from Pin J2-34 of CCM-2 to the front frame ground location #2. CCM-2 activates the Brake Light Circuit. Hydrostatic Control Lever Pulled Back Quickly Wiring harness - Electrical schematic frame 07 (A.30.A.88 - C.20.E.07) Wiring harness - Electrical schematic frame 25 (A.30.A.88 - C.20.E.25) The RHM sends 5 volts from pin 16 of connector X026 through a wire splice to pin A on the Ground Speed Pot R-04.
The potentiometer’s ground path exits pin B and travels through a wire splice to reach pin 6 of connector X026 of the RHM. The RHM monitors the signal between pin 1 of connector X027 and pin C of the Ground Speed Pot R-04. When the hydrostatic control lever is pulled back quickly, the RHM sends a message across CAN to CCM-2. CCM-2 activates the Brake Light Circuit. Emergency Shutdown When the combine senses a serious problem, CCM-2 forces the engine to automatically shutdown. During these conditions, CCM-2 will activate the Brake Light Circuit.
Brake Light Circuit Activation Wiring harness - Electrical schematic frame 35 (A.30.A.88 - C.20.E.35) Wiring harness - Electrical schematic frame 38 (A.30.A.88 - C.20.E.38) When the brake lights are activated, CCM-2 sends current from connector X015 pin J1-18 to pin 1 of the Brake Lights Relay K-33. The brake light relay energizes and latches pins 3 and 5. Current flows from the electrical system buss bar and passes through fuse F-52 to reach pin 3 of the Brake Lights Relay. Current crosses from pin 3 to pin 5 and travels through connectors X004 and X024 to reach a wire splice. The wire splice sends the current to 3 paths:
The first path sends current through connector X285 to reach pin 54 of the trailer outlet (J-09). This activates the trailer brake lights (if equipped). The second path sends current through connector X071 to reach a wire splice. The wire splice sends current to the LH Brake/Tail Lamp (E-11) (North American) and the LH Rear Flashing Lamp (E-05) (European). The ground path to the lamp passes through a wire splice and connector X071 to reach the rear frame ground location #1. This causes the lamp to illuminate. The third path sends current through connector X071 to reach a wire splice.
The wire splice sends current to the RH Brake/Tail Lamp (E-12) (North American) and the RH Rear Flashing Lamp (E-06) (European). The ground path to the lamp passes through a wire splice and connector X071 to reach the rear frame ground location #1. This causes the lamp to illuminate. 9668 1 27/05/2004 A.40.A / 18