Case IH AFX8010 — LIGHTING SYSTEM

DISTRIBUTION SYSTEMS - LIGHTING SYSTEM Lower Work Lights (E-23, E-24) - Wiring harness - Electrical schematic frame 40 (A.30.A.88 - C.20.E.40) When the Work Light Switch (S-43) is activated, CCM-1 sends current from connector X018 pin J1-5 to reach pin 1 of the Road Lights Relay (K-27). From pin 1, current flows to pin 1 of the Header Work Lights Relay (K-22). Current travels from pin 1 to reach pin 1 of the Lower Work Lights Relay (K-30). The relay energizes and latches terminals 3 and 5. Current flows from the electrical system buss bar and passes through the Lower Work Lights Relay (K-30) and travels through connector X004 to reach a wire splice.

The wire splice splits the current into two different paths: The first path sends current to pin 1 of the LH Lower Work Light (E-23). The ground path to the light exits pin 2 and travels to the Front Frame Ground Location #2. This causes the LH Lower Work Light to illuminate. The second path sends current to pin 1 of the RH Lower Work Light (E-24) The ground path to the RH Lower Work Light (E-24) exits pin 2 and travels to the Front Frame Ground Location #2. This causes the light to illuminate. Side Work Lights (E-25, E-26) - Activated when header is raised above a programmable height or the road light switch is moved to the "Left" or "Right" Turn Signal position.

For more information, refer to: Side work light - Overview (A.40.A.18 - C.10.A.10) Rear Work Lights (E-27, E-28) - The Rear work lights will come on when the Work Light Switch (S-43) is ON and the combine is put in reverse. For more information, refer to: Rear work light - Overview (A.40.A.17 - C.10.A.10) Unload Tube Light (E-29) - If the front work lights are ON and the unload tube is extended outward, the Unload Tube Light will illuminate. For more information, refer to: Rear work light - Overview (A.40.A.17 - C.10.A.10) Grain Tank Light (E-30) - When the Work Light Switch (S-43) is activated, CCM-1 sends current from connector X018 pin J1-5 to reach pin 1 of the Road Lights Relay (K-27).

From pin 1, current flows to pin 1 of the Header Work Lights Relay (K-22). Current travels from pin 1 to reach pin 1 of the Lower Work Lights Relay (K-30). The relay energizes and latches terminals 3 and 5. Current flows from the electrical system buss bar and passes through the Lower Work Lights Relay (K-30) and travels through connector X004 to reach a wire splice. The wire splice directs the current through connector X009 to reach pin 1 of the Grain Tank Light (E-30). The ground path to the grain tank light exits pin 2 and passes through connector X009 to reach the Front Frame ground location #2. This causes the Grain Tank Light (E-30) to illuminate.

Back Lighting Circuits - Activated when the front work lights are turned on. For more information, refer to: Back light - Overview (A.40.A.24 - C.10.A.10) On The Road Switch (S-12) and/or Hazard Switch (S-25) in the "ON" position Cab Outer Work Lights (E-15, E16) - When the Work Light Switch (S-43) is activated, CCM-1 sends current from connector X018 pin J1-11 to reach pin 86 of the Cab Roof Work Light Relay (K-01). The relay energizes and latches terminals 30 and 87. Current sent from the electrical buss bar passes through the Cab Roof Light Fuse (F-31), and travels through the Cab Roof Work Lights Relay (K-01), and splits into two paths:

The first path sends current through the LH Cab Roof Light Fuse (F-06), connector X002 , and connector X036 to reach pin A of the LH Cab Outer Work Light (E-15). The ground path exits pin B and passes through a wire splice and connector X036 to reach the cab roof ground location #4. This causes the LH Cab Roof Light to illuminate. The second path sends current through the RH Cab Roof Light Fuse (F-07), connector X002 , and connector X036 to reach pin A of the RH Cab Outer Work Light (E-16). The ground path exits pin B and passes through a wire splice and connector X036 to reach the cab roof ground location #4. This causes the RH Cab Roof Light to illuminate.

Cab Inner Work Lights (E-17, E-18) Low Beam - When the Work Light Switch (S-43) is activated, CCM-1 sends current from connector X018 pin J1-5 to reach pin 1 of the Road Lights Relay (K-27). The relay energizes and latches terminals 3 and 5. Current sent from the Distance Work Lights Relay (K-21) passes through the Road Lights Relay (K-27) and travels through connectors X003 and X036 to reach a wire splice. The wire splice splits the current into two paths: The first path sends current to pin B of the LH Cab Inner Work Light (E-17). The ground path to the LH Cab Inner Work Light exits pin C and travels through a wire splice and connector X036 to reach the cab ground location #4.

This causes the LH Cab Inner Work Light to illuminate (Low Beam). The second path sends current to pin B of the RH Cab Inner Work Light (E-18). The ground path to the RH Cab Inner Work Light exits pin C and travels through a wire splice and connector X036 to reach the cab ground location #4. This causes the RH Cab Inner Work Light to illuminate (Low Beam). Taillights (E-11, E-12) (E-03, E-04) - When the Work Light Switch (S-43) is in the Second or Third position, CCM-1 sends current from connector X018 pin J1-21 to pin 1 of the Light Control Relay (K-02). The relay 9668 1 27/05/2004 A.40.A / 21