DISTRIBUTION SYSTEMS - LIGHTING SYSTEM Head light Relay - Testing (A.40.A.11.82 - G.40.A.20) AFX8010 9668 1 27/05/2004 A.40.A / 32 Problem Possible Cause Correction One or More Beacon Lights Do Not Operate Beacon Light Relay Beacon Relay - Testing (A.40.A.15.82 - G.40.A.20) Beacon Light Switch Beacon Switch - Testing (A.40.A.15.83 - G.40.A.20) Bulbs and Wiring Beacon Wiring harness - Testing (A.40.A.15.88 - G.40.A.20) One or More Side Lights Do Not Operate Work Light Switch Front work light Switch - Testing (A.40.A.16.83 - G.40.A.20) Side Work Light Relay Side work light Relay - Testing (A.40.A.18.82 - G.40.A.20) Bulbs and Wiring Side work light Wiring harness - Testing (A.40.A.18.88 - G.40.A.20) Unload Tube Light Does Not Operate Unload Tube Light Unloading tube light - Testing (A.40.A.35 - G.40.A.20) One or More Front Work Lights Do Not Operate Work Light Switch Front work light Switch - Testing (A.40.A.16.83 - G.40.A.20) Work Light Relay Front work light Relay - Testing (A.40.A.16.82 - G.40.A.20) Bulbs and Wiring Front work light Wiring harness - Testing (A.40.A.16.88 - G.40.A.20) One or More Under Shield Lights Do Not Operate Light Switch Under shield service light Switch - Testing (A.40.A.19.83 - G.40.A.20) Bulbs and Wiring Under shield service light Wiring harness - Testing (A.40.A.19.88 - G.40.A.20) Engine Component Light Does Not Operate Engine Light Switch Engine component service light Switch - Testing (A.40.A.21.83 - G.40.A.20) Engine Light Wiring Harness Engine component service light Wiring harness - Testing (A.40.A.21.88 - G.40.A.20) N° Test Point Expected Result Other Result (Possible Cause) 1 Turn Road Light Switch S-26 to Low Beam position.
Measure for 12 volts at Low Beam Relay K-05 (pin 5). 12 volts If good reading, relay is functioning properly. Low Beam Relay K-05. Adjacent circuits. Go to test 2 2 Turn Road Light Switch S-26 to Low Beam. position. Measure for 12 volts at Low Beam Relay K-05 (pin 1). 12 volts If good reading, Go to test 3 Open or short to ground in circuit 169 (YE) between Low Beam Relay K-05 (pin 1) and Road Light Switch S-26 connector X256 (pin 7). A short to ground will blow the Fuse #51. Road Light Switch S-26. 3 Measure for 12 volts at Low Beam Relay K-05 (pin 3). 12 volts If good reading, Go to test 4 Open circuit 236 (RD) between Low Beam Relay K-05 (pin 3) and Fuse #33.
A short to ground will blow the Fuse #33. 4 Disconnect the Low Beam Relay K-05. Measure resistance on circuit 156 (BK) between Low Beam Relay K-05 (pin 2) and ground. Less than 1ohm.. If good reading, replace Low Beam Relay K-05 Go to test 5 Open in circuit 156 (BK) between Low Beam Relay K-05 (pin 2) and ground. 5 Turn Road Light Switch S-26 to .High Beam. position Measure for 12 volts at High Beam Relay K-04 (pin 5). 12 volts If good reading, relay is functioning properly. High Beam Relay K-04. Adjacent circuits. Go to test 6