DISTRIBUTION SYSTEMS - LIGHTING SYSTEM Head light Switch - Testing (A.40.A.11.83 - G.40.A.20) AFX8010 9668 1 27/05/2004 A.40.A / 33 N° Test Point Expected Result Other Result (Possible Cause) 6 Turn Road Light Switch S-26 to High Beam position. Measure for 12 volts at High Beam Relay K-04 (pin 1). 12 volts If good reading, Go to test 7 Open or short to ground in circuit 191 (YE) or 218 (YE) between High Beam Relay K-04 (pin 1) and Road Light Switch S-26 connector X256 (pin 4). A short to ground will blow the Fuse #51. Road Light Switch S-26. 7 Measure for 12 volts at High Beam Relay K-04 (pin 3).
12 volts If good reading, Go to test 8 Open circuit 185 (RD) between High Beam Relay K-04 (pin 3) and Fuse #32. A short to ground will blow the Fuse #32. 8 Disconnect the High Beam Relay K-04. Measure resistance on circuit 192 (BK) between High Beam Relay K-04 (pin 2) and ground. Less than 1ohm. If good reading, replace the High Beam Relay K-04. Open in circuit 192 (BK) between High Beam Relay K-04 (pin 2) and ground. N° Test Point Expected Result Other Result (Possible Cause) 1 Measure for 12 volts at Road Light Switch S-26 connector X256 (pin 5). 12 volts If good reading, .
Go to test 3 Open or short to ground on circuit 213 (RD) between Road Light Switch S-26 connector X256 (pin 5) and Fuse #51 2 Disconnect Road Light Switch S-26. Measure for 12 volts at Road Light Switch S-26 connector X256 (pin 5). 12 volts If good reading, replace Road Light Switch. Open or short to ground on circuit 213 (RD) between Road Light Switch S-26 connector X256 (pin 5) and Fuse #51. 3 Reconnect Road Light Switch S-26. Measure for 12 volts at Road Light Switch S-26 connector (pin 8). 12 volts If good reading, Go to test 5 Open or short to ground on circuit 214 (RD) between Road Light Switch S-26 connector X256 (pin 8) and Fuse #51. 4 Disconnect Road Light Switch S-26.
Measure for 12 volts at Road Light Switch S-26 connector X256 (pin 8). 12 volts If good reading, replace Road Light Switch. Go to test 5 Open or short to ground on circuit 214 (RD) between Road Light Switch S-26 connector X256 (pin 5) and Fuse #51. 5 Place Key in ON position. Measure for 12 volts at Road Light Switch S-26 connector X256 (pin 6). 12 volts If good reading, Go to test 7 Open or short to ground on circuit 96 (OR) or 55 (OD) between Road Light Switch S-26 connector X256 (pin 6) and Key Switch S-02 connector X068 (pin 6). 6 Disconnect Road Light Switch S-26. Measure for 12 volts at Road Light Switch S-26 connector X256 (pin 6). 12 volts If good reading, replace Road Light Switch.
Go to test 7 Open or short to ground on circuit 96 (OR) or 55 (OD) between Road Light Switch S-26 connector X256 (pin 6) and Key Switch S-02 connector X068 (pin 6). 7 Place Key in ON position and Road Light Switch S-26 in the RIGHT turn position. Measure for 12 volts at Road Light Switch S-26 connector X256 (pin 3). 0 to 12 volts If good reading, Go to test 8 Short to ground on circuit 197 (PU) between Road Light Switch S-26 connector X256 and CCM1 (pin J1-2) and Flasher Module A-05 connector X255 (pin 8). 8 Place Key in ON position and Road Light Switch S-26 in the LEFT turn position. Measure for 12 volts at Road Light Switch S-26 connector X256 (pin 2).
0 to 12 volts If good reading, Go to test 9 Road Light Switch S-26 Short to ground on circuit 201 (PU) between Road Light Switch S-26 connector X256 (pin 2) and CCM1 (pin J1-9) and Flasher Module A-05 connector X255 (pin 7).