DISTRIBUTION SYSTEMS - ELECTRONIC SYSTEM 11. Disconnect the cab roof harness from the cab main harness at connector X003 (it will be necessary to remove the upper trim panel in the cab to gain access to this connector). Install a jumper wire on the cab roof end of connector X003 between pins 1 & 2. Use a multimeter to check for continuity between connector X003 pins 4 & 6 (cab roof end). A. If there is no continuity, there is an open circuit in the cab roof (CR) harness between connector X003 pins 1 & 4 wire 131 yellow and 137 yellow or between connector X003 pins 2 & 6 wires 132 green and 138 green. Locate the open and repair. B. If there is continuity, continue with step 12. 12.
Reattach connector X003, and disconnect the cab main harness from the CCM2 module at connector X015. Install a jumper wire on the cab main end of connector X015 pins J1-13 & J1-14. Use a multimeter to check for continuity between connector X018 pins J1-13 & J1-14. A. If there is no continuity, there is an open circuit in the cab main (CM) harness between connector X018 and connector X003 wires 137 yellow and 138 green, or between connector X003 and connector X015 wires 131 yellow and 132 green. Locate the open and repair. B. If there is continuity, continue with step 13. 13. Disconnect the main frame harness from the CCM2 module at connector X016.
Use a multimeter to check for continuity between connector X016 pins J2-23 & J2-32. A. If there is continuity (approx. 120 ohms), there is a fault in the CCM2 module. Replace the module. B. If there is no continuity, continue with step 14. 14. Disconnect the main frame harness from the expansion harness at connector X034A. Use a multimeter to check for continuity on the expansion harness end of connector X034A pins 11 & 12. A. If there is continuity (approx. 120 ohms), there is an open circuit in the main frame (MF) harness between connector X009 and connector X034A wires 1230 yellow and 1231 green. Locate the open and repair. B. If there is no continuity, continue with step 15. 15.
Disconnect the expansion harness from the main frame harness at connector X034. Use a multimeter to check for continuity on the main frame harness end of connector X034 pins 11 & 12. A. If there is continuity (approx. 120 ohms), there is an open circuit in the expansion (EX) harness between connector X034A and connector X034 wires 1230 & 819 yellow and 1231 & 820 green. Locate the open and repair. B. If there is no continuity, continue with step 16. 16. Disconnect the main frame harness from the engine harness at connector X010. Use a multimeter to check for continuity on the engine harness end of connector X010 between pins 19 & 21. A. If there is continuity (approx.
120 ohms), there is an open circuit in the main frame (MF) harness between connector X034 and connector X010 wires 819 yellow and 820 green. Locate the open and repair. B. If there is no continuity, continue with step 17. 17. Disconnect the engine harness from the ECU module at connector X193. Use a multimeter to check for continuity on the ECU module connector X193 between pins 11 & 12. A. If there is continuity (approx. 120 ohms), there is an open circuit in the engine (EN) harness between connector X010 and connector X193 wires 819 yellow and 820 green. Locate the open and repair. B. If there is no continuity, there is a fault in the ECU module. Replace the module.
Wiring Harness -- Electrical Schematic Frame 30 (A.30.A.88 -- C.20.E.30) Wiring Harness -- Electrical Schematic Frame 31 (A.30.A.88 -- C.20.E.31) A.50.A / 114