Yanmar — Yanmar Diesel Inboard Shop Manual for One, Two, and Three Cylinder Engines

SINGLE-CYLINDER ENGINES 97 ing it out with an appropriate size drift or pin punch. When removing a large core plug, the use of a universal impact slide hammer is recommended. 4. Coat the inside diameter of the plug bore and the outer diameter of the new plug with sealer. Use an oil-resistant sealer if the plug is to be installed in an oil gallery or a wa- ter-resistant sealer for plugs installed in the water jacket. 5. Install the new core plug with an appropriate size core plug installation tool (Figure 92), driver or socket. The outside edge ofthe plug should be 2-3 mm (0.08-0.12 in.) inside the block. 6. Repeat Steps 1-5to replace each remaining core plug. 3.

Clean the plug bore thoroughly to remove all traces of the old sealer. Inspect the bore for any damage that might interfere with proper sealing of the new plug. Table 1 ENGINE SPECIFICATIONS (1GM, 1GM10) Bore Stroke Displacement Number of cylinders Cylinder bore diameter Bore out-of-round-max. Cylinder block warpage-max. Piston diameter Standard Wear limit Piston top clearance Piston ring side clearance Top ring Second ring Oil ring Ring end gap (all rings) Piston pin diameter Piston pin hole diameter In piston In rod Piston pin clearance In rod In piston 75 mm (2.95 in.) 72 mm (2.83 in.) 318 cc (19.4 cu.

ln.) 1 75.000-75.030 mm (2.9528-2.9540 in.) 0.02 mm (0.0008 in.) 0.07 mm (0.0028 ln.) 74.910-74.940 mm (2.9492-2.9504 ln.) 74.850 mm max. (2.9468 ln.) 0.68-0.88 mm (0.027-0.035 in.) 0.065-0.100 mm (0.0026-0.0039 in.) 0.035-0.070 mm (0.0014-0.0028 in.) 0.020-0.055 mm (0.0008-0.0022 ln.) 0.20-0.40 mm (0.008-0.016 in.) 19.991-20.000 mm (0.7870-0.7874 ln.) 19.995-20.008 mm (0.7872-0.7877 ln.) 20.000 mm (0.7874 in.) 0.025-0.047 mm (0.0010-0.0019 in.) 0.005 mm tight-O.017 mm loose (0.0002 in. tight-0.0007 in. loose) Piston ring width Top & second ring Oil control ring . Crankshaft main journal diameter Timing gear end Flywheel end Journal out-of-round-max.

Crankshaft end play Crankshaft runout-max. Main bearing clearance Timing gear end Flywheel end Crankshaft thrust bearlng-min. Front Inner Crankpin diameter Journal out-of-round-max. Crankpin bearing clearance Connecting rod side clearance Cylinder head warpage-max.

1.97-1.99 mm (0.0776-0.0783 in.) 3.97-3.99 mm (0.1563-0.1571 ln.) 43.950-43.964 mm (1.7303-1.7309 in.) 59.950-59.964 mm (2.3602-2.3608 ln.) 0.01 mm (0.0004 In.) 0.06-0.19 mm (0.0024-0.0075 in.) 0.15 mm (0.006 in.) 0.036-0.092 mm (0.0014-0.0036 in.) 0.036-0.095 mm (0.0014-0.0037 in.) 2.75 mm (0.108 in.) 2.25 mm (0.089 in.) 39.950-39.964 mm (1.5728-1.5734 in.) 0.01 mm (0.0004 in.) 0.028-0.086 mm (0.0011-0.0034 in.) 0.2-0.4 mm (0.008-0.016 in.) 0.07 mm (0.003 in.) (continued)