Yanmar — Yanmar Diesel Inboard Shop Manual for One, Two, and Three Cylinder Engines

128 CHAPT ER SIX 5. Position the engine so the valve lifters will not fall out when the camshaft is withdrawn. 6. Remove the bea ring retaining screw (Figure 74 ), then withdraw the cam shaft. 7. Remove the valve lifters and mark them so they may be reinstalled in their original locations. NOTE If precision measuring equipment is not avail able, hOI '1! Step 8 pe rformed by a deal - ership or machine shop. 8. Check the bearing joumal(s) and lobes for signs of wear or sconng. 9. Measure the bearing joumal(s) and lobes (Figure 75) and compare the results 10 the specifications in Tables CYLINDER BLOCK 1-3. Replace the camshaft if the journal or lobes do not meet specifications.

Cleaning and Inspection 10. Measure the stem diameter of the valve lifters and co mpare it to the specification in T ab les 1-3. Measure the lifter bores in the cylinder block. Calculate the lifter clear- ance and compare it with the specification in Tables 1-3. Replace the valve lifters if they do not meet spcciflca- tions. Replace the valve lifter if the lifter face is scored, galled, excessively worn or otherwise damaged. I. Clean the block thoroughly with solvent. Remove any gasket or RTV sealant residue from the machined sur- faces. Check all core plugs for leaks and replace any that arc suspect. See Core Plug Replacement in this chapter.

Check oil and coolant passages for sludge, dirt and corro- sion while cleaning. If the passages are very dirty, have the block boiled out by a machine shop. Blowout all pas- sages with compressed air. Check the threads in the head bolt holes to be sure they are clean. If dirty, use a tap to reo store the threads and remove any deposits. 2. Examine the block for cracks. To confirm suspicions about possible leakage areas, usc a mixture of one part kerosene and two parts engine oil. Coat the suspected area with this solution. then wipe dry and immediately apply a solution of zinc oxide dissolved in wood alcohol.

If any discoloration appears in the treated area, the block is cracked and should be replaced, II . Replace the ball bearing if it is damaged or feels rough during rotation. 12. Installation is the reverse of removal. Note the fol- lowing: a. If installing a new camshaft. coat the camshaft lobes with camshaft break-in lubricant. If reinstalling the original camshaft, apply heavy oil to the camshaft lobes. b. Lubricate the camshaft bearing joumal(s) with heavy engine oil before reinstallation. NOTE On 2GAf. 3GM and 3JfM engines, remm'e the cylinder liners to check the cylinder block deck/ or warpage in Step 3. c. Lightly tap the end of the camshaft to seat the ball bearing in the engine.

Rotate the camshaft to be sure it rotates freely. d. Align the timing marks (Fi2ure 76) on the camshaft and crankshaft gears when installing the camshaft gear. 3. Check the flatness of the cylinder block deck or top surface. Place an accurate straightedge on the block. If there is any gap between the block and straightedge, rnea- sure it with a flat feeler gauge (Ffgure 78). Measure from end to end and from comer to comer. Have the block re- surfaced i fit is warped more than 0.07 mm (0.0028 in.). 4. On 2GM20. 3GM30 and 3HM35 models- Measure the cylinder bores with a bore gauge (f igure 79) for out-of-roundness or excessive wear as described in Pis- ton/Clylinder Bore Check in this chapter.

If the cylinders exceed maximum tolerances. they must be rebored. c. Install the fuel in je ction cam so the side marked with a zero is out (Fi 2ure 77, typical). f. Check gear backlash by installing a dial indicator as she .... -n in Fig ur e 67 or by rotating the gear teeth with soft solder between the gear teeth. Compare the measurement with the specification in Tables 1-3. If gear backlash is incorrect. replace the cam- shaft and crankshaft gears.