E LEC TRICAL SYSTEM 191 ur e 16 or 7, Figur e 17) and spring. if so equipped. 7. Remove the yoke and spring, if so equipped. from the solenoid. 8A. To install the solenoid on models equipped with an antitorque spring. reverse the disassembly procedure while noting the following: 6. Remove the solenoid with the actuating yoke (6, f ig- a. Position the antito rque spring on the solenoid plunger so the spring ends fit in the holes in the sole- noid (f igure 18). b. Position the yoke in the solenoid plunger so the notch on the yoke fits against the closed end of the anti-torque spring as shown in Figure 18. c.
Make sure the open end of the yoke properly en- gages the cars on the overrunning clutch body (Fig- ure 19). 8B. To install the solenoid on models not equipped with an antitorq uc spring, reverse the disassembl y procedure while noting the following: a. Make sure that the pads on the open end of the yoke properly fit between the flanges on the overrunning clutch body . 2. Disconnect the solenoid terminal wires. See Fig ure 15. J. Remove the starter motor mounting bolts. Pull the starter motor away from the flywheel and remove it from the engine. 4. Installation is the reverse of removal. Tighten mount- ing bolts to torque specified in Tab le 2.
9 Bru sh Repl acem ent Solenoid Removal/Ins talla tio n IG.\I. IG ,\l10 . 1G .\I . 1G.\110. 3G . \I and 3G .\l 30 mod els To remove the solenoid it is necessary to partially disas- semble the starter. Note that the starter used on series 10 M, lGM I O, 2GM . 2GM20. J GM and 3GM3 0cn gines arc equipped with an antitorq uc spring that stabilizes the actuating yoke. Brush replacement requires partial disassembly of the starter. 1. Disconnect the positive lead from the solenoid. 2. Remove the cover (26, fi gure 16) on the end cap. 3. Detach the E-ring (25, Figure 16) and remove the washers from the arma ture shaft. 4. Remove the brush holder retaining screws (30, Figure 16). 5.
Remove the two throughbolts (29. Figure 16). 6. Separate the end cover (21,Fi gure 16) from the starter. 7. Note the position of the brushes in the brush holder. Use a suitable tool to pull back and hold the brush retain- ing clip. then remove the brush. See figur e 20, typical. Repeat this step to remove the rema ining brus hes. 8. Remove the brush holder from the armature shaft. 9. Use an ohmmeter or self-powered test lamp to check for continuity between the insulated brush holder and the base of the brush holder assembl y. See fi gure 21. If there is continuity. replace the brush holder. 10. Inspect brush and brush spring condition. Measure brush length.
Replace all brushes if any are oil-soaked or worn to 12 mm (0.47 in.) or less in length. Replace any broken or distorted brush springs. I. Remove the starter as previously described. 2. Disconnect the solenoid term inal wires (Figure 15). 3. Remove the screws securing the solenoid to the starter. The solenoid will be loose but still attached to the actuat- ing yoke in the starter. It is necessary to partially disas- semble the starter to remove the solenoid and yoke. 4. Remove the 1\\'0 throughbolts (29. f igure 16 or 33, Ftg ur e 17).
NOTE Do not allow the armature to move forward because the commutator may slide out of the brushes, which will require disassembly of the rear of the starter to reinstall the brushes. 5. Caref ully separa te the drive end c ove r (3. fi gur e 16) from the frame ( 15or 22) so the armature shaft withdraws from the drive end housing, but stays in position in the frame.