204 CHAPTER TEN Intermediate shaft 1. Remove and discard the Q-ring (Figure 14) at the end of the shaft. 2. Remove the thrust washer, gear and roller bearings. 3. Inspect the bearings, shaft and reverse idler gear inside diameter for excessive wear, grooves, metal transfer and discoloration from overheating. If necessary, replace the shaft, gear and bearings. 4. Check the idler gear teeth for excessive wear, corro- sion or rust and mechanical damage. Check the teeth for galling, chips, cracks, missing pieces, distortion or discol- oration from overheating. If necessary, replace the gear. 5. Reassemble the intermediate shaft. Install a new a-ring on the shaft.
Intermediate shaft Roller bearings O-ring 8. Inspect the forward and reverse gear inside diameters for excessive wear, grooves, metal transfer and discolor- ation from overheating. If necessary, replace the gears. 9. Install the cone clutch on the output shaft and check movement of the clutch on the output shaft. If the clutch does not move smoothly, inspect the splines on the clutch and shaft for burrs, scoring, galling or other signs of dam- age. If dressing will not correct the damaged splines, re- place the clutch and/or shaft. 10. Inspect the tapered surface ofthe forward and reverse gears for galling, scoring or other damage that will pre- vent smooth cone clutch engagement.
If necessary, re- place the gears. 11. Install the cone clutch into the forward and reverse gears. Measure clutch depth as shown in Figure 18. Com- pare the measurement with the specification in Table 3. Replace the part, in necessary. 12. Measure the width of the shifter groove in the cone clutch (Figure 19) and compare with the specification in Table 4. 13. Inspect the roller bearings and inner bearing races for excessive wear, grooves, metal transfer and discoloration from overheating. If necessary, replace the bearings and mner races. 14. Measure the wear surface of the thrust washers. If wear exceeds 0.20 mm (0.008 in.) on the thin thrust washer, replace the washer.
If wear exceeds 0.05 mm (0.002 in.) on the thick thrust washer, replace the washer. 15. On KM2P and KM3P transmissions-Measure the width of the spring cups and compare them with the speci- fications in Table 5. 16. On KM2P and KM3P transmissions-Measure the width of the spring cup retainers and compare them with the specifications in Table 5. If any surface wear on the retainer exceeds 0.10 mm (0.004 in.), replace the retainer. 17. Assemble the output shaft by reversing the disassem- bly procedure while noting the following: Output shaft Refer to Figure 15. 1. Using a suitable puller (Figure 16), remove the bear- ing, spacer and reverse gear from the output shaft. 2.
The retaining nut at the end of the shaft is staked. Use a chisel to cut away the staked portion so the nut will rotate. To hold the output shaft, position the coupling flange in a vise, then set the output shaft into the splines in the flange as shown in Figure 17. NOTE The retaining nut has left-hand threads. 3. Unscrew the retaining nut by rotating the nut clock- wise (left-hand threads). 4. Using a suitable puller, pull the bearing, spacer and forward gear off the output shaft. 5. Remove the pin from the shaft. NOTE Mark the clutch cone in Step 6 according to forward or reverse end so it can be rein- stalled in its original position. 6.
While holding the clutch cone, tap the end of the shaft with a soft-faced hammer to remove the inner roller bear- ing race, spacer and cone clutch. A suitable puller or press may also be used. Remove the remaining inner bearing race and spacer. 7. Check the forward and reverse gear teeth for excessive wear, corrosion and mechanical damage. Check the teeth for galling, chips, cracks, missing pieces, distortion or dis- coloration from overheating. If necessary, replace the gears.