SEBU7901-01 47 Maintenance Section Refill Capacities If it is necessary to choose a single grease, always choose a grease that meets or exceeds the requirements of the most demanding application. Remember that lubricants that barely meet the minimum performance requirements can be expected to barely meet the minimum life of the part. False economy is being used if a grease is purchased with the lowest cost as the only consideration. Instead, use the grease that yields the lowest total operating cost. This cost should be based on an analysis that includes the costs of parts, labor, downtime, and the cost of the amount of grease that is required.
NOTICE Operating with fuels that do not meet Caterpillar’s rec- ommendations can cause the following effects: start- ing difficulty, poor combustion, deposits in the fuel in- jectors, reduced service life of the fuel system, de- posits in the combustion chamber, and reduced ser- vice life of the engine. NOTICE Heavy Fuel Oil (HFO), Residual fuel, or Blended fuel must NOT be used in Caterpillar diesel engines (ex- cept in 3600 Series HFO engines). Blended fuel is residual fuel that has been diluted with a lighter fuel (cutter stock) so that they will flow. Blended fuels are also referred to as heavy fuel oils.
Severe component wear and component failures will result if HFO type fuels are used in engines that are configured to use distillate fuel. Because some greases are not chemically compatible, purge all of the old grease from a joint when the following conditions exist. The grease in a joint is changed from one type of grease to another type of grease. The grease that will be used in the joint will be supplied by a supplier that did not supply the grease that is currently in the joint. In extreme cold ambient conditions, you may use the distillate fuels that are specified in Table 6. However, the fuel that is selected must meet the requirements that are specified in Table 6.
These fuels are intended to be used in operating temperatures that are down to н 54 °C ( н 65 °F). Consult your supplier in order to determine if the greases are compatible. If in doubt, Purge! Table 6 Note: All Caterpillar greases are compatible with each other. Fuel In North America, diesel fuel that is identified as No. 1-D or No. 2-D in “ASTM D975” with the S15 designation generally meet the specifications. Caterpillar recommends diesel fuels that are distilled from crude oil. Diesel fuels from other sources could exhibit detrimental properties that are not defined or controlled by this specification.
(1) The fuels that are listed in this table may not meet all of the requirements that are specified in this table . Consult the supplier for the recommended additives in order to maintain the proper fuel lubricity. In the USA, 0.05 percent diesel fuels have been used in all on-highway truck engines since 1 January 1994. This low sulfur diesel fuel was mandated as a means of directly reducing particulate emissions from diesel truck engines. This low sulfur fuel will also be used in Caterpillar commercial diesel engines and in Caterpillar machine engines. This diesel fuel will be used when low emissions are required. This fuel will be used when the fuel supplier can provide this type of fuel.
Caterpillar has not seen any detrimental effects with 0.05 percent sulfur fuel in Caterpillar diesel engines. These fuels are lighter than the No. 2 grades of fuel. The cetane number of the fuels in Table 6 must be at least 40. If the viscosity is below 1.4 cSt at 40 °C (104 °F), use the fuel only in temperatures below 0 °C (32 °F). Do not use any fuels with a viscosity of less than 1.2 cSt at 40 °C (104 °F). Note: Fuel cooling may be required in order to maintain the minimum viscosity of 1.4 cSt at the fuel injection pump. There are many other diesel fuel specifications that are published by governments and by technological societies.
Usually, those specifications do not review all the requirements that are addressed in this specification. To ensure optimum engine performance, a complete fuel analysis should be obtained before engine operation. Distillate Fuels (1) Specification Grade “MIL-DUL-5624T” JP-5 “ASTM D1655-05” Jet-A-1 “MIL-DTL-83133E” JP-8