Mitsubishi — Mitsubishi Diesel Engine Service Manual

SERVICE STANDARDS Unit: mm (in.) 1 - 14 Group Item Nominal value Standard value Limit Remarks Engine main parts Crankshaft Crank journal diameter (STD) φ52 (2.0488) 51.985 to 52.000 (2.0482 to 2.0488) ― Crank pin diameter φ48 (1.8912) 47.950 to 47.964 (1.8892 to 1.8897) ― Crankshaft bend 0.025 (0.0010) 0.050 (0.0020) Correct or replace Main bearings oil clearance 0.030 to 0.077 (0.0012 to 0.0030) 0.100 (0.0040) Replace main bearings Connecting rod bearings oil clearance 0.025 to 0.072 (0.0010 to 0.0028) 0.150 (0.0059) Replace connecting rod bearings End play 0.050 to 0.175 (0.0020 to 0.0069) 0.500 (0.0197) Replace flanged No.

3 main bearings Timing gear backlash Crank gear to idler gear 0.040 to 0.120 (0.0015 to 0.0047) 0.300 (0.0120) Replace Idler gear to valve camshaft gear Idler gear to pump camshaft gear Valve camshaft gear to PTO gear 0.080 to 0.190 (0.0032 to 0.0075) Pump camshaft gear to oil pump gear 0.070 to 0.200 (0.0028 to 0.0079) Camshaft cam height (including lobe) 35.720±0.1 (1.4073±0.0394) 34.720 (1.3679) Replace Fuel injection pump shaft cam height (including lobe) 44±0.1 (1.7336±0.0039) 43 (1.6942) Replace Flywheel flatness 0.150 (0.0059) or less 0.500 (0.0197) Correct Tappet-to-guide clearance ― 0.150 (0.0059) Replace tappet Camshaft journal-to-bushing clearance 0.050 to 0.125 (0.0020 to 0.0049) 0.150 (0.0059) Replace bushing Idler gear-to-shaft clearance 0.020 to 0.070 (0.0008 to 0.0028) 0.200 (0.0079) Replace idler gear or idler shaft Fuel system Injection valve opening pressure MPa (kgf/cm2) [psi] 14.22 (145) [2062] 14.22 to 15.00 (145 to 153) [2062 to 2176] ― Adjust with washer Oil system Relief valve opening pressure MPa (kgf/cm2) [psi] 0.35±0.05 (3.5±0.5) [50±7.2] ― Replace Oil pressure switch closing pressure MPa (kgf/cm2) [psi] 0.05±0.01 (0.5±0.1) [7±1.4] ― Replace Cooling system Thermostat Valve opening temperature 82±1.5℃ (179.6±2.7°F) ― Replace 8 mm (0.32 in.) valve lift temperature 95℃ (203°F) ― Thermoswitch At 111±3.5℃ (231.8±6.3°F) 30 MΩ [when dipped in oil of 105℃ (221°F)] ― Replace Fan belt deflection {when pressed with a force of approx.

98 N (10 kgf) [22] between crankshaft and alternator pulleys and between crankshaft and fan pulleys} 10 to 12 (0.4 to 0.5) ― Replace